Dodge 2010 Caliber Owner'S Manual Download Page 204 | Manualshive

Page: 204 / 470

background image

•

Gate Ajar (with a single chime)

•

Headlamps or Park Lamps On

•

Key In Ignition

•

Check TPM System

•

Oil Change Required

Oil Change Required — If Equipped

Your vehicle is equipped with an engine oil change
indicator system. The “Change Oil” message will flash in
the instrument cluster odometer for approximately 5 sec-
onds after a single chime has sounded to indicate the next
scheduled oil change interval. The engine oil change
indicator system is duty cycle based, which means the
engine oil change interval may fluctuate dependent upon
your personal driving style.

Unless reset, this message will continue to display each
time you turn the ignition switch to the ON/RUN
position. To turn off the message temporarily, press and
release the Trip Odometer button on the instrument
cluster. To reset the oil change indicator system (after
performing the scheduled maintenance), refer to the
following procedure.

1. Turn the ignition switch to the ON position (do not
start the engine).

2. Fully depress the accelerator pedal slowly three times
within 10 seconds.

3. Turn the ignition switch to the OFF/LOCK position.

NOTE:

If the indicator message illuminates when you

start the vehicle, the oil change indicator system did not
reset. If necessary, repeat this procedure.

4

UNDERSTANDING YOUR INSTRUMENT PANEL

203

«
...
202
203
204
205
206
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: N-Com Pages: 28

Brand: AAMP of America Pages: 6

Brand: AccuAir Pages: 40

Brand: Peak Pages: 10

Cherokee 16 1982

Brand: Jeep Pages: 1311

Brand: Dynojet Pages: 68

Brand: Kuda-Phonebase Pages: 3

MOLLE PANELS RAM 2500

Brand: PUTCO Pages: 4

Brand: Westfalia Pages: 18

Brand: Toyota Pages: 371

Brand: U.S. General Pages: 4

GMC Yukon Denali 2005

Brand: Cadillac Pages: 456

Brand: Saab Pages: 63

Brand: R&G Pages: 20

Brand: Whispbar Pages: 70

Brand: Havis Pages: 5

Brand: TrailFX Pages: 2

2008 B2300 Truck

Brand: Mazda Pages: 280

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands