Dodge 2010 Caliber Owner'S Manual Download Page 305 | Manualshive

Page: 305 / 470

background image

ESC Off Indicator Light

The “ESC Off Indicator Light” (located in the
instrument cluster) starts to flash as soon as the
tires lose traction and the ESC system becomes
active. The “ESC Off Indicator Light” also

flashes when TCS is active. If the “ESC Off Indicator
Light” begins to flash during acceleration, ease up on the
accelerator and apply as little throttle as possible. Be sure
to adapt your speed and driving to the prevailing road
conditions.

WARNING!

•

The Electronic Stability Control (ESC) cannot pre-
vent the natural laws of physics from acting on the
vehicle, nor can it increase the traction afforded by
prevailing road conditions.

(Continued)

WARNING! (Continued)

•

ESC cannot prevent accidents, including those
resulting from excessive speed in turns, driving on
very slippery surfaces, or hydroplaning. Only a
safe, attentive, and skillful driver can prevent
accidents.

•

The capabilities of an ESC-equipped vehicle must
never be exploited in a reckless or dangerous
manner, which could jeopardize the user’s safety
or the safety of others.

ESC Malfunction Indicator Light

The “ESC Malfunction Indicator Light” in the
instrument cluster will come on when the
ignition switch is turned to the ON position. It
should go out with the engine running. If the

“ESC Malfunction Indicator Light” comes on continu-
ously with the engine running, a malfunction has been
detected in the ESC system. If this light remains on after

304

STARTING AND OPERATING

«
...
303
304
305
306
307
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: Camcar Pages: 6

Brand: Lancia Pages: 276

Brand: T-Tech Pages: 38

Brand: Hama Pages: 2

Brand: OEM Tools Pages: 4

Electronic Parking Disc 3

Brand: Jacob Jensen Pages: 2

Brand: Yakima Pages: 12

Brand: 3SIXT Pages: 12

Brand: Ford Pages: 38

Brand: Thule Pages: 8

SmartShot Automatic 12V 1.5 Amp 5 Stage

Brand: Yuasa Pages: 44

Brand: Ford Pages: 368

Brand: Jeep Pages: 16

Brand: Audi Pages: 4

Brand: tams elektronik Pages: 44

Brand: Mercedes-Benz Pages: 358

Brand: AIS Pages: 2

Grand Cherokee SRT 2019

Brand: Jeep Pages: 656

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands