Dodge 2010 Caliber Owner'S Manual Download Page 29 | Manualshive

Page: 29 / 470

background image

WARNING! (Continued)

•

When leaving the vehicle, always remove the key
from the ignition lock and lock your vehicle. Do
not leave unattended children in the vehicle or
with access to an unlocked vehicle. Unsupervised
use of vehicle equipment may cause severe per-
sonal injuries and death.

CAUTION!

An unlocked vehicle is an invitation to thieves.
Always remove the key from the ignition and lock all
of the doors when leaving the vehicle unattended.

Power Door Locks

A power door lock switch is on each front door trim
panel. Press this switch to lock or unlock the doors and
liftgate.

NOTE:

To prevent from locking the key in the vehicle,

the power door lock switch will not operate when the key
is in the ignition and either front door is open. A chime
will sound as a reminder to remove the key.

Driver Power Door Lock Switch

1 - Unlock

2 - Lock

28

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
27
28
29
30
31
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: Kargo Master Pages: 6

Brand: Raven Pages: 24

Brand: Weather Guard Pages: 4

Brand: Jabra Pages: 10

Brand: Pacbrake Pages: 14

Brand: Webasto Pages: 34

Brand: TBC Pages: 12

Brand: Prorack Pages: 14

Brand: STO N SHO Pages: 7

Brand: HAUL MASTER Pages: 8

Brand: Ecco Pages: 12

Brand: Hella Pages: 21

Brand: Mobility Networks Pages: 52

2000 Oldsmobile Intrigue

Brand: Oldsmobile Pages: 348

Brand: Volvo Pages: 123

Brand: Acura Pages: 7

Brand: Haltech Pages: 12

1967 Calais Coupe

Brand: Cadillac Pages: 255

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands