Dodge 2010 Caliber Owner'S Manual Download Page 132 | Manualshive

Page: 132 / 470

background image

Six-Way Power Seats — If Equipped

The power seat switch is located on the outboard side of
the seat near the floor. Use the switch to move the seat up,
down, forward, rearward, or to tilt the seat.

WARNING!

Adjusting a seat while the vehicle is moving is
dangerous. The sudden movement of the seat could
cause you to lose control. The seat belt might not be
properly adjusted and you could be injured. Adjust
the seat only while the vehicle is parked.

CAUTION!

DO NOT place any article under a power seat or
impede its ability to move as it may cause damage to
the seat controls. Seat travel may become limited if
movement is stopped by an obstruction in the seat’s
path.

Power Seat Switch

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

131

«
...
130
131
132
133
134
...
»

Summary of Contents for 2010 Caliber























































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Caliber

Brand: Kargo Master Pages: 6

Brand: Xblitz Pages: 16

Brand: Carefree Pages: 12

2005 Sierra Denali

Brand: GMC Pages: 428

Brand: Mercedes-Benz Pages: 346

Brand: Thule Pages: 4

Brand: Axxess Pages: 4

Brand: Vintage Air Pages: 14

Brand: Kolpin Outdoors Pages: 6

Brand: Schartec Pages: 2

Brand: Phonocar Pages: 6

Brand: Dometic Pages: 158

Brand: AC Schnitzer Pages: 20

2010 Civic Sedan

Brand: Honda Pages: 390

Brand: A-Tach Pages: 2

RGBW Rock Lights

Brand: Lit Lightz Pages: 3

Brand: Ecco Pages: 24

Brand: travall Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands