28
Manual for Data Communication dv40.fm
AT+CGEQMIN
Registers criterion determining
whether to permit QoS (Quality of
Service) sent from network when
establishing packet
transmission.
*2
Refer to “More on AT Commands”.
(
n
P. 34)
Refer to “More on
AT Commands”.
(
n
P. 34)
AT+CGEQREQ
Sets QoS (Quality of Service)
requested of network during
packet transmission.
*2
Refer to “More on AT Commands”.
(
n
P. 35)
Refer to “More on
AT Commands”.
(
n
P. 35)
AT+CGMR
Displays FOMA terminal
version.
*2
―
AT+CGMR
o
12345678901234
56
OK
AT+CGREG=
<n>
Sets whether to send network
registration status. Service area
information (inside/outside) is
sent.
*1
<n>
0: Does not set (default setting)
1: Sets
When “AT+CGREG=1” is set, information
is sent in the format “+CGREG:<stat>”.
0, 1, 4 or 5 can be set for the <stat>
parameter.
<stat>
0: Outside area
1: Inside area (home)
4: Unknown
5: Inside area (visitor)
AT+CGREG=1
o
OK
(Set to send)
AT+CGREG?
o
+CGREG:1,0
OK
(Indicates outside
area)
+CGREG:1
(Moved from
outside area to
inside area)
AT+CGSN
Displays the FOMA terminal’s
serial number.
*2
―
AT+CGSN
o
123456789012345
OK
AT+CLIP=<n>
Shows PC calling number when
receiving 64K data
communications.
*1
<n>
0: Does not output results (default setting)
1: Outputs results
DiCLIP
：
<n>,<m> for
“AT+CLIP?”
<m>
0: NW setting to not send own number
during transmissions
1: NW setting to send own number during
transmissions
2: Unknown
AT+CLIP=0
o
OK
AT+CLIP?
o
+CLIP:0,1
OK
AT+CLIR=<n>
Sets whether to send terminal’s
phone number when establishing
64K data communications.
*2
<n>
0: Follows the service agreement
1: Does not send
2: Sends (default setting)
DiCLIR: <n>,<m> for AT+CLIR?
<m>
0: CLIR is not running (always send)
1: CLIR is always running (never send)
2: Unknown
3: CLIR temporary mode (default setting is
“Do not send”)
4:
CLIR temporary mode (default setting is “Send”)
AT+CLIR=0
o
OK
AT+CLIR?
o
+CLIR:2,3
OK
AT+CMEE=<n>
Sets the manner to display FOMA
terminal error reports.
*1
Sets whether to display errors only as
“ERROR”, or to display reason with text or
numerical value.
<n>
0: Displays “ERROR” and no result codes
(default setting)
1: Displays result codes with numerical
values
2: Displays result codes with text
When reports are set to display by setting
“n=1” or “n=2”, they are displayed in the
following format:
+CME ERROR:xxxx (xxxx is a numerical value
or text. Refer to “Error Reports”
n
P. 34.)
AT+CMEE=0
o
OK
AT+CNUM
o
ERROR
AT+CMEE=1
o
OK
AT+CNUM
o
+CME ERROR:10
AT Command
Overview
Parameter/Explanation
Execution
Example
[M]
[M]
[M]
[M]
[M]
[M]
[M]
[M]
Manual for Data Communication dv40.fm 28 ページ ２００６年１０月１０日 火曜日 午後８時４６分
