Docomo FOMA P905ITV, Instruction Manual

Page: 576 / 596

43
3
Set an access point name (APN).
≥
If the FOMA phone is not connected, this display does not appear.
Adding, editing, and deleting an access point
name (APN)
･ To add an access point name (APN), click “ 追加 (Add)”.
･ To edit (correct) a registered access point name (APN), click “ 編集
(Edit)”.
･ To delete a registered access point name (APN), select the target
access point name (APN), then click “
削除 (Delete)”.
※
You cannot delete the access point name (APN) registered in
“cid1” and “cid3”. (Even if you select “cid3” and click “ 削除
(Delete)”, it is not deleted actually and “mopera.net” returns.)
Saving data into a file
From the menu, select “
ファイル
(File)”
→
“
上書き保存
(Overwrite
and save)” or “ 名前を付けて保存 (Rename and save)”; you can back
up the access point name (APN) setting registered in the FOMA
phone or save the currently edited access point name (APN) setting.
Reading data from a file
From the menu, select “ ファイル (File)” → “ 開く (Open)”; you can
obtain the access point name (APN) setting saved in the personal
computer.
Reading access point name (APN) information
from the FOMA phone
From the menu, select “ ファイル (File)” → “FOMA 端末から設定を取
得
(Obtain the setting from the FOMA phone)”; you can obtain the
access point name (APN) setting from the FOMA phone.
Writing access point name (APN) information to
the FOMA phone
Click “FOMA
端末へ設定を書き込む
(Write the setting to the FOMA
phone)”; you can write the displayed access point name (APN)
setting to the FOMA phone.
You cannot write the IP information to the FOMA phone which does
not support the IP connection.
Dial-up information creation function
Select an access point name you add or edit on the access point
name (APN) setting display, then click “
ダイヤルアップ作成
(Create
dial-up information)”; you can create dial-up information for packet
communication. If the access point name (APN) setting is not written
to the FOMA phone, the FOMA phone setting writing confirmation
display then appears, then click “ はい (Yes)”. After writing ends, the “
パケット通信ダイヤルアップ作成画面 (packet communication
dial-up information creation display)” appears.
Enter any access point name, then click “
アカウント・パスワードの
設定 (Specify account and password)”. (You can leave it blank to
connect to “mopera U” or “mopera.”)
Enter the user name and password, select the authorized user, and
then click “OK”.
If your Internet service provider instructs you to specify IP and DNS
information, click “
詳細情報の設定
(Set detailed information)”, and
register the required information. Then click “OK”.
After entering information, click “OK”. Dial-up is created.
See page 37 for using “mopera U” or “mopera”.
See page 38 for using a provider other than “mopera U” or “mopera”.
The operation below explains how to set a connection
for packet communication without using the “FOMA PC
setup software”.
The packet communication uses AT commands to carry
out the settings from a personal computer. To specify
settings, communication software to enter AT command
is required.
When using DoCoMo Internet access service “mopera
U” or “mopera”, you do not need to set an access point
name (APN) (See page 44).
You can set “caller ID notified/not notified” (see
page 44) as required. (You need to set “caller ID
notified” when using “mopera U” or “mopera”.)
<Packet communication setting flow using AT commands>
Information
≥
The access point name (APN) is information to be registered in the
FOMA phone, so if you connect another FOMA phone, you need to
register the access point name (APN) again.
≥
To continue using the access point name (APN) of the personal
computer, register the same access point name (APN) for the same cid
number in the FOMA phone.
Setting Dial-up Network
Set Packet Communication
Confirm the COM port number
Start the communication software that enables the
entry of AT commands
Set an access point name (APN)
Set “caller ID notified/not notified”
Set others
Exit the communication software
■ AT commands
≥
The AT commands are used to control a modem. The FOMA phone,
which conforms to the AT commands, supports some extended
commands and unique AT commands.
≥
By entering AT commands, you can carry out detailed setting for packet
communication and FOMA phone, and confirm (display) the setting
contents.
≥
If the entered AT command is not displayed, enter “ATE1 ”.