Docomo FOMA P905ITV, Instruction Manual

Page: 553 / 596

20
Reading access point name (APN) information
from the FOMA phone
From the menu, select “ ファイル (File)” → “FOMA 端末から設定を取
得
(Obtain the setting from the FOMA phone)”; you can obtain the
access point name (APN) setting from the FOMA phone.
Writing access point name (APN) information to
the FOMA phone
Click “FOMA
端末へ設定を書き込む
(Write the setting to the FOMA
phone)”; you can write the displayed access point name (APN)
setting to the FOMA phone.
You cannot write the IP information to the FOMA phone which does
not support the IP connection.
Dial-up information creation function
Select an access point name (APN) you add or edit on the access
point name (APN) setting display, then click “
ダイヤルアップ作成
(Create dial-up information)”; you can create dial-up information for
packet communication. If the access point name (APN) setting is not
written to the FOMA phone, the FOMA phone setting writing
confirmation display then appears, then click “ はい (Yes)”. After
writing ends, the “ パケット通信ダイヤルアップ作成画面 (packet
communication dial-up information creation display)” appears.
Enter any access point name, then click “
アカウント・パスワードの
設定 (Specify account and password)”. (You can leave it blank to
connect to “mopera U” or “mopera.”)
Enter the user name and password, select the authorized user, and
then click “OK”.
If your Internet service provider instructs you to specify IP and DNS
information, click “
詳細情報の設定
(Set detailed information)”, and
register the required information. Then click “OK”.
After entering information, click “OK”. Dial-up is created.
See page 12 for using “mopera U” or “mopera”.
See page 13 for using a provider other than “mopera U” or “mopera”.
Information
≥
The access point name (APN) is information to be registered in the
FOMA phone, so if you connect another FOMA phone, you need to
register the access point name (APN) again.
≥
To continue using the access point name (APN) of the personal
computer, register the same access point name (APN) for the same cid
number in the FOMA phone.
The operation below explains how to set a connection
for packet communication without using the “FOMA PC
setup software”.
The packet communication uses AT commands to carry
out the settings from a personal computer. To specify
settings, communication software to enter AT command
is required. “Hyper Terminal”, which is attached to
Windows as the standard software, is used here for
explanation.
When using DoCoMo Internet access service “mopera
U” or “mopera”, you do not need to set an access point
name (APN) (see page 22).
You can set “caller ID notified/not notified” (see
page 23) as required. (You need to set “caller ID
notified” when using “mopera U” or “mopera”.)
<Packet communication setting flow using AT commands>
Setting Dial-up Network
Set Packet Communication
Confirm the COM port number (See page 21)
Start the communication software that enables the entry of AT commands
(See step 3 of “Set an Access Point Name (APN)” on page 22)
Set an access point name (APN) (See step 7 on page 23)
Set “caller ID notified/not notified”
(See step 2 of “Set Caller ID Notified/Not Notified” on page 23)
Set others (See page 48)
Exit the communication software (See step 9 on page 23)
■
AT commands
≥
The AT commands are used to control a modem. The FOMA phone,
which conforms to the AT commands, supports some extended
commands and unique AT commands.
≥
By entering AT commands, you can carry out detailed setting for packet
communication and FOMA phone, and confirm (display) the setting
contents.
≥
If the entered AT command is not displayed, enter “ATE1 ”.