DH Instruments PG7000 Operation And Maintenance Manual Download Page 149

Page: 149 / 224

4. REMOTE OPERATION

Page 139

∗

STB?

Purpose

Read the Status Byte Register.

Syntax

“

∗

STB?”

Remarks

The Status Byte Register reflects the general status of the PG. The ‘MSS’ bit state is
represented by bit 6.

Query Reply

(0 to 255)

Example Command:

Reply:

“*STB?”
“4”

∗

TST?

Purpose

Read the power on self test status.

Syntax

“

∗

TST?””

Remarks

The PG7000 system memory stores the user settings (units, mode, resolution) and
retains them when the unit is shut off. On power up, this memory is checked. If this
memory is corrupted, all user settings are reset to default (as if the “

∗

RST” program

message was executed), and the

∗

TST query returns a ‘1’. If PG7000 passed the test

on power up OR if the

∗

TST query was used at least once since the unit was powered

up the reply is ‘0’.

Query Reply

“0” or “1”

Example Command:

Reply:

“*TST?”
“1”

Summary of Contents for PG7000

































































































































































































































Search results

Summary of Contents for PG7000

Reviews:

Related manuals for PG7000

Brands by name

Popular brands

DH Instruments PG7000, Operation And Maintenance Manual

Search results

Summary of Contents for PG7000

Reviews:

Related manuals for PG7000

Brands by name

Popular brands