![background image](http://html1.mh-extra.com/html/daikin/fhq100buv1b-x-2/fhq100buv1b-x-2_service-manual_2459261116.webp)
SiBE28-804
Field Settings
Test Operation
105
d. “List of contents of retry and malfunction”
Take the following steps to check contents of retry and malfunction.
8
: ON
1
: OFF
9
: BLINK
Malfunction
code
Contents of retry or malfunction
1
2
3
HAP H1P H2P H3P H4P H5P H6P H7P HAP H1P H2P H3P H4P H5P H6P H7P HAP H1P H2P H3P H4P H5P H6P H7P
C4
Indoor heat exchanger thermistor
9 9 8 7 7 7 9 7 9 9 8 7 7 9 7 7 9 9 8 8 7 7 7 7
E1
Faulty outdoor PC board
9 9 7 8 7 7 9 9 9 9 8 7 7 7 7 9 9 9 8 8 7 7 7 7
E3
Abnormal high pressure
9 9 8 7 7 7 9 9 9 9 8 8 7 7 7 7
E4
Abnormal low pressure
9 9 8 7 7 9 7 7 9 9 8 8 7 7 7 7
E5
Compressor motor lock
9 9 8 7 7 9 7 9 9 9 8 8 7 7 7 7
E7
Abnormal outdoor
fan motor
DC motor 1 lock
9 9 8 7 7 9 9 9 9 9 8 8 7 7 7 9
DC motor 2 lock
9 9 8 8 7 7 9 7
Abnormal inverter transmission
9 9 8 8 7 7 9 9
E9
Abnormal electronic
expansion valve
Disconnected electronic expansion valve connector
9 9 8 7 9 7 7 9 9 9 8 8 7 7 7 9
Malfunction due to wet conditions
9 9 8 8 7 7 9 7
F3
Abnormal discharge
pipe temperature
Abnormal discharge pipe temperature
9 9 7 8 7 9 7 9 9 9 8 7 7 7 9 9 9 9 8 8 7 7 7 9
Disconnected discharge pipe thermistor
9 9 8 8 7 7 9 7
H3
Abnormal high pressure switch
9 9 7 8 7 9 7 7 9 9 8 7 7 7 9 9 9 9 8 8 7 7 7 7
H9
Abnormal outdoor air thermistor
9 9 8 7 9 7 7 9 9 9 8 8 7 7 7 7
J1
Abnormal pressure sensor
9 9 7 8 7 9 9 7 9 9 8 7 7 7 7 9 9 9 8 8 7 7 7 7
J3
Abnormal discharge pipe thermistor
9 9 8 7 7 7 9 9 9 9 8 8 7 7 7 7
J5
Abnormal suction pipe thermistor
9 9 8 7 7 9 7 9 9 9 8 8 7 7 7 7
J6
Abnormal heat exchanger distributor pipe thermistor
9 9 8 7 7 9 9 7 9 9 8 8 7 7 7 7
J7
Abnormal intermediate heat exchanger thermistor
9 9 8 7 7 9 9 9 9 9 8 8 7 7 7 7
J8
Abnormal liquid pipe thermistor
9 9 8 7 9 7 7 7 9 9 8 8 7 7 7 7
L1
PC board failure
9 9 7 8 7 9 9 9 9 9 8 7 7 7 7 9 9 9 8 8 7 7 7 7
L4
Elevated radiation fin temperature
9 9 8 7 7 9 7 7 9 9 8 8 7 7 7 7
L5
Compressor instantaneous overcurrent
9 9 8 7 7 9 7 9 9 9 8 8 7 7 7 7
L8
Compressor overload
9 9 8 7 9 7 7 7 9 9 8 8 7 7 7 7
L9
Compressor lock
9 9 8 7 9 7 7 9 9 9 8 8 7 7 7 7
LC
Abnormal transmission (between the control and the inverter)
9 9 8 7 9 9 7 7 9 9 8 8 7 7 7 7
P1
Unbalanced power supply voltage
9 9 7 8 9 7 7 7 9 9 8 7 7 7 7 9 9 9 8 8 7 7 7 7
P4
Abnormal radiation fin thermistor
9 9 8 7 7 9 7 7 9 9 8 8 7 7 7 7
PJ
Faulty capacity setting
9 9 8 7 9 9 7 9 9 9 8 8 7 7 7 7
U0
Abnormal gas
shortage
Gas shortage warning
9 9 7 8 9 7 7 9 9 9 8 7 7 7 7 7 9 9 8 8 7 7 7 9
Abnormal gas shortage
9 9 8 8 7 7 9 7
U2
Abnormal power
supply voltage
Inverter undervoltage and overvoltage
9 9 8 7 7 7 9 7 9 9 8 8 7 7 7 9
SP-PAM overvoltage
9 9 8 8 7 7 9 7
U4
Abnormal transmission (between indoor and outdoor units)
9 9 8 7 7 9 7 7 9 9 8 8 7 7 7 7
UA
Faulty field setting switch
9 9 8 7 9 7 9 7 9 9 8 8 7 7 7 7
UF
Improper piping and improper communication wiring
9 9 9 9 9 9 8 8 7 7 7 7
To enter "Monitor mode," push the MODE (BS1)
button when in "Setting mode 1."
Push the SET (BS2) button to set the LED
display to retry or malfunction item.
When the RETURN (BS3) button is pushed, the
LED display for RETURN 1 turns ON.
<Selection of retry or malfunction item>
When SET (BS2) button is pushed, the LED
display for RETURN 2 turns ON.
<Display of RETURN 2>
When SET (BS2) button is pushed, the LED
display for RETURN 3 turns ON.
Push the RETURN (BS3) button to return the
system to the initial state of "Monitor mode."
∗
Pushing the MODE (BS1) button will bring the
system to the "Setting mode 1."
<Display of RETURN 3>
<Display of RETURN 1>
Summary of Contents for FHQ100BUV1B x 2
