Cisco ASR 900 Series Release Notes Download Page 89 | Manualshive

Page: 89 / 310

Cisco ASR 900 Series Release Notes Download Page 89

C H A P T E R

1

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

10

Restrictions and Caveats in Cisco IOS XE 3.7S
Releases

This chapter provides information about restrictions and caveats in Cisco IOS XE 3.7S releases.

Note

Because Cisco IOS XE 37S is based on Cisco IOS XE 3.5 inherited releases, some caveats that apply to
Cisco IOS XE 3.5 releases also apply to Cisco IOS XE 37S. Release 3.5 is not described in this
document; for a list of the software caveats that apply to Cisco IOS XE 3.5, see the

Release Notes for

Cisco IOS XE Release 3S

.

Note

We recommend that you view the field notices for the current release to determine whether your software
or hardware platforms are affected. You can access field notices at

http://www.cisco.com/en/US/support/tsd_products_field_notice_summary.html.

This chapter contains the following sections:

•

Limitations and Restrictions, page 2

•

Caveats in Cisco IOS XE 3.7S Releases, page 5

«
...
87
88
89
90
91
...
»

Summary of Contents for ASR 900 Series























































































































































































































































































































Reviews:

No comments