manualshive.com logo in svg

Cisco ASR 900 Series, Release Notes, Page: 274 / 310

Share
Download
Cisco ASR 900 Series Release Notes Download Page 274

 

20

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

  Caveats in Cisco IOS XE 3.10S Releases

Resolved Caveats—Cisco IOS XE Release 3.10S

This section documents the issues that have been resolved in Cisco IOS XE Release 3.10S. 

•

CSCtx70302

Symptom:

 Traceback and log messages are seen while performing a multilink bundle shutdown on 

the Cisco ASR 903 router.

Conditions

: This issue is observed when traffic flows over the multilink bundle. 

Workaround:

 There is no workaround. This issue does not impact the operation of the router.

•

CSCua61934

Symptom: 

When a policy map with priority in class-default is attached to an interface, it is not 

rejected.

Conditions: 

This issue is observed when you configure policy-map having priority in class-default 

and attach the policy to an interface.

Workaround:

 There is no workaround.

•

CSCua90879

Symptom: 

QoS policies with a police statement on the class-default class do not take effect.

Conditions: 

This issue is observed when you apply a police statement to the class-default class 

within a QoS policy on an ingress EVC interface.

Workaround: 

Apply the police statement to a static class, such as class cos0.

•

CSCuc59386

Symptom: 

IOMD crashes continuously on OC-3 IM. The interfaces on OC-3 IM are not 

configurable and the following error message is displayed:

stand-by does not support this command

Conditions: 

This issue is observed on a Cisco ASR 903 router high availability setup with OC-3 IM. 

Workaround: 

Reload the standby RSP. 

•

CSCuc60148

Symptom: 

The router does not shut down when the temperature sensor reaches the shutdown 

threshold.

Conditions: 

Temperature sensor reaches shutdown threshold.

Workaround: 

Use the 

facility-alarm critical exceed-action shutdown

 commands to enable 

system shutdown.

•

CSCuc83088

Symptom: 

The router drops traffic while performing a Stateful Switchover (SSO).

Conditions: 

This issue is observed when the router is running HSRP or VRRP. It occurs when the 

destination MAC address is a virtual MAC (vMAC) address.

Workaround: 

Change the traffic priority and detour traffic before performing an SSO. 

•

CSCud09100

Symptom:

 The router accepts a policy with marking at two levels. It should not accept a policy with 

marking at two levels.

Conditions:

 This issue is observed when you apply a policy with marking at two levels.

Summary of Contents for ASR 900 Series























































































































































































































































































































Reviews:

No comments