manualshive.com logo in svg

Cisco ASR 900 Series, Release Notes, Page: 259 / 310

Share
Download
Cisco ASR 900 Series Release Notes Download Page 259

 

5

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

  Caveats in Cisco IOS XE 3.10S Releases

•

CSCui41169

Symptom: Active card reloads when standby comes active after switchover with scaled 
configuration

Conditions: This issue occurs when 4000K EVCs with 1-level ingress policy, and 2-level egress 
policy is configured on the router. Ingress policy should have 1-level policer, egress policy should 
have one parent and child policer. The issue occurs after a reload of the card with this configuration.

Workaround: There is no workaround.

•

CSCui44409

Symptom: No console message are seen on insertion or removal of USB

Conditions: This issue is observed standby RSP. 

Workaround: More Info: 

•

CSCui45075

Symptom: When an IM is removed from the router, the MST states are not reflected in the standby 
RSP. If a switchover happens at this state, it could cause total traffic drop. 

Conditions: This issue is seen when HA is configured on the router.

Workaround: There is no workaround. 

•

CSCui98883

Symptom: System crashes on configuring TOD.

Conditions: This issue occurs on dual RSP setup and PTP is configured.

Workaround: There is no workaround. 

•

CSCui99309

Symptom: IPv6 BFD with static client does not display when VRF is configured.

Conditions: This issue occurs when VRF is configured on the router.

Workaround: There is no workaround. 

•

CSCuj30644

Symptom: Multicast does not function in scaled mode and when BDI is configured on the core.

Conditions: This issue was seen in the scaled mode.

Workaround: Execute the 

no ip igmp snooping

 command on the router to forward the multicast 

traffic.

•

CSCuj34652

Symptom: IPv6 traffic drops for the packets with next header options. Next header options include 
Hop-by-hop options, fragment header.

Conditions: This issue occurs when option packets are punted to CPU and generates the time 
exceeded message.

Workaround: There is no workaround.

•

CSCuj38988, CSCum45935

Symptom: QL does not move to QL-FAILED state when the Gigabit ethernet interface is shutdown. 

Conditions: This issue occurs when the Gigabit ethernet interface is shutdown.

Workaround: There is no workaround.

•

CSCuj42208

Summary of Contents for ASR 900 Series























































































































































































































































































































Reviews:

No comments