manualshive.com logo in svg

Cisco ASR 900 Series, Release Notes, Page: 127 / 310

Share
Download
Cisco ASR 900 Series Release Notes Download Page 127

 

39

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter 

  Caveats in Cisco IOS XE 3.7S Releases

  •

CSCue77612

Symptom

: MAC address synchronization on 1 Gigabit Ethernet port on standby RSP causes traffic 

to be forwarded to incorrect port after a switchover.

Conditions

: This issue occurs after a switchover.

Workaround

: Clear MAC address after a switchover is performed.

  •

CSCue86696

Symptom:

 Interface flaps after longevity run is performed.

Conditions:

 This issue occurs after prolonged tests are performed with SPF interface modules.

Workaround:

 There is no workaround.

  •

CSCue87542

Symptom:

 Deleting bridge domain interfaces (BDIs) with routing traffic causes a flood to CPU 

resulting in control plane traffic loss.

Conditions: 

This issue occurs after a ping failure and the Bidirectional Forwarding Detection 

(BFD) protocol or OSFP protocol flaps on deleting the BDI while IPv4 traffic is flowing.

Workaround:

 Delete the Trunk EFP interface and then the BDI.

  •

CSCue89503

Symptom:

 The power supply status displays critical after removing and inserting the power supply 

on the Cisco ASR903 router.

Conditions:

 This issue occurs after multiple OIR of the power supply is performed.

Workaround:

 There is no workaround. This issue is cosmetic.

  •

CSCuf05039

Symptom:

 I2C-WRITE and MDIO_READ error messages are displayed on the Cisco ASR903 

router.

Conditions:

 This issue occurs after an interface module hard or soft OIR is performed.

Workaround:

 There is no workaround.

  •

CSCuf61365

Symptom:

 Virtual circuit counters do not increment after interface module Online Insertion and 

Removal (OIR) followed by a SSO is performed.

Conditions:

 This issue occurs after an OIR followed by a SSO is performed.

Workaround:

 Perform a SSO without a interface module OIR.

  •

CSCuf65040

Symptom:

 1 Gigabit Ethernet or 10 Gigabit Ethernet interface module enters out of service state.

Conditions: 

This issue occurs when a hard Online Insertion and Removal (OIR) is performed on the 

interface module.

Workaround: 

Perform another hard OIR or a Stateful Switchover (SSO) followed by a soft OIR.

Summary of Contents for ASR 900 Series























































































































































































































































































































Reviews:

No comments