manualshive.com logo in svg

Cisco ASR 900 Series, Release Notes, Page: 216 / 310

Share
Download
Cisco ASR 900 Series Release Notes Download Page 216

 

20

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

  Caveats in Cisco IOS XE 3.9S Releases

•

CSCue51682

Symptom:

 The REP protocol flaps, as indicated by the following error messages:

*Feb  8 06:51:38.857: %REP-4-LINKSTATUS: GigabitEthernet0/0/1 (segment 10) is 

non-operational due to neighbor not responding

*Feb  8 06:51:39.096: %REP-4-LINKSTATUS: GigabitEthernet0/0/1 (segment 10) is 

operational.

Conditions:

 Occurs under the following conditions:

–

The router is sending traffic using the incremental MAC address table

–

Fast LSL is configured using a 200ms timer.

–

The router is configured with more than 2000 MAC addresses.

Workaround:

 Remove fast LSL from the REP configuration. 

•

CSCue54649

Symptom:

 Traceback is seen on new active RSP console after performing a SSO.

Conditions:

 This issue is seen when OC-3 IM is configured on OC-12 mode. The POS and serial 

interfaces mayor may not be configured.

Workaround:

 There is no workaround. 

•

CSCue61803

Symptom:

 IMs do not get powered off when router is reloaded.

Conditions:

 This issue is seen occasionally on reload. 

Workaround:

 There is no workaround.

•

CSCue65149

Symptom:

 OBJ messages are observed when changing the interval in EVC BD offload cases (scale).

Conditions:

 This issue occurs when 3.3ms session interval and MEPS is configured on the router 

and then the MEPS and domain configuration is removed and a session interval of 10ms interval is 
configured.

Workaround:

 Configure a low session interval.

•

CSCue66137

Symptom:

 The IOMD crashes with CPU hog messages.

Conditions:

 This issue occurs with OC-3 interface module and traffic is sent over a multilink bundle 

with packet size greater than 600 byte.

Workaround:

 There is no workaround. 

•

CSCue73478

Symptom:

 Standby RSP Sync LED become holdover after switchover.

Conditions:

 This issue occurs after a switchover.

Workaround:

 There is no workaround.

•

CSCue77596

Symptom:

 Cos value gets wrongly marked for a QinQ packet

Conditions:

 This issue occurs on a service instance with dot1q encapsulation and no rewrite is 

configured on the interface.The policy map attached in the ingress has marking in it. 

Workaround:

 There is no workaround. 

Summary of Contents for ASR 900 Series























































































































































































































































































































Reviews:

No comments