manualshive.com logo in svg

Cisco ASR 900 Series, Release Notes, Page: 303 / 310

Share
Download
Cisco ASR 900 Series Release Notes Download Page 303

 

5

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

  Caveats in Cisco IOS XE 3.12S Releases

Conditions:

 This issue occurs when the host queue is congested by ICMP punt traffic for a long 

time.

Workaround:

 There is no workaround.

•

CSCul27129

Symptom:

 Remote MEPs are not learnt on cross-connect service with a POS interfaces the core 

link.

Conditions:

 This issue occurs when CFM up MEPs are configured for an cross-connect service 

configured on an access interface, with POS links in core.

Workaround:

 There is no workaround.

•

CSCul37563

Symptom: 

Packet drop observed after resetting the multilink bundle more than 3 or 4 times.

Conditions:

 This issue occurs on an MLPPP interface over channelized STM.

Workaround:

 Configure the remote end to accept compressed packets.

•

CSCul40676

Symptom:

 Ping failure observed on the interface connected with port 0/0/0 with ACR configuration.

Conditions: 

This issue occurs when ACR is configured on the router.

Workaround:

 Install the IM in the other bay or use a port other than 0/0/0 as the core.

•

CSCul64840

Symptom: 

The router shuts down when the SNMP host is enabled by executing the 

snmp-server 

host

 command globally.

Conditions:

 This issue occurs when the 

snmp-server host

 command is executed.

Workaround:

 Use the management interface VRF for the SNMP host.

•

CSCul68008

Symptom: 

Bulk synchronization fails for ATM layer 2 configuration on T1E1 IM is observed on 

the router.

Conditions:

 This issue occurs on TDM IM with ATM configuration.

Workaround:

 There is no workaround.

•

CSCul93778

Symptom:

 No alarm is reported after executing the 

shutdown

 command on the controller, when 

high availability (HA) is setup.

Conditions:

 This issue occurs when a POS interface is created on an HA setup, and a 

shutdown 

command is executed on the interface after SSO. 

Workaround:

 There is no workaround.

•

CSCum66060

Symptom:

 Increased usage of MPLSintd observed after scale configuration and stress test. Interface 

flaps and BFD flaps are observed on the router.

Conditions:

 This issue occurs with increased usage in MPLSintd resource leading to router crash 

over a prolong period of time.

Workaround:

 There is no workaround.

Summary of Contents for ASR 900 Series























































































































































































































































































































Reviews:

No comments