manualshive.com logo in svg

Cisco ASR 900 Series, Release Notes, Page: 262 / 310

Share
Download
Cisco ASR 900 Series Release Notes Download Page 262

 

8

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

  Caveats in Cisco IOS XE 3.10S Releases

Workaround: There is no workaround.

•

CSCul21429

Symptom: The router console freezes and the OSPF or BFD sessions flap.

Conditions: This issue occurs when TOD type is changed dynamically on a PTP master from NTP 
to Cisco or vice-versa.

Workaround: Unconfigure TOD and reconfigure a new TOD type.

•

CSCul21447

Symptom: The ANNOUNCE message does not get updated.

Conditions: This issue occurs in the PTP slave.

Workaround: There is no workaround. 

•

CSCul40676

Symptom: Ping failure observed on the interface connected with port 0/0/0 with ACR configuration.

Conditions: This issue occurs when ACR is configured on the router.

Workaround: Install the IM in the other bay or change the port other than 0/0/0 as the core.

•

CSCul46353

Symptom: Traffic drop observed on priority queues.

Conditions: This issue occurs on QoS policy with 2-level priority queues (priority level classes) that 
do not guarantee the bandwidth on 1-level priority against 2-level traffic.

Workaround: There is no workaround.

•

CSCul46643

Symptom: Convergence with SSO for REP with multicast is greater than 3 seconds.

Conditions: This issue occurs on performing an SSO on the Receiver

Workaround: There is no workaround.

•

CSCul49147

Symptom: Time exceed message is generated when IPv6 packets are received on the router.

Conditions: This issue occurs when IPv6 packets have option headers.

Workaround: If the IPv6 options have fragment header then increase the MTU size. 

•

CSCul50181

Symptom: A Cisco router may see unicast traffic not being forwarded out of the Gigabit ethernet 
interface while multicast traffic is being processed by the router correctly. 

Conditions: This issue occurs when the router has BDI configured to the Gigabit ethernet interface. 

Workaround: Reload the router.

•

CSCul51784

Symptom: IPv6 packets fails to get forwarded out of the router.

Conditions: This issue occurs when unicast RPF enabled for IPv4 traffic and IPv6 traffic is received 
on the interface.

Workaround: Remove unicast RPF checks on the interface where dual stack is configured.

•

CSCul52778

Symptom: STM -1 port keeps on increasing on changing the 

card typ

e command multiple times.

Summary of Contents for ASR 900 Series























































































































































































































































































































Reviews:

No comments