manualshive.com logo in svg

Cisco ASR 900 Series, Release Notes, Page: 126 / 310

Share
Download
Cisco ASR 900 Series Release Notes Download Page 126

 

38

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter  

  Caveats in Cisco IOS XE 3.7S Releases

  •

CSCue50128

Symptom:

 FMFP download failure occurs on reaching 1980 odd number even though 2000 ternary 

content addressable memory (TCAM) space is allocated for ACLs in the IP template.

Conditions: 

This issue occurs in normal conditions when the scale reaches 1980.

Workaround:

 There is no workaround. 

  •

CSCue52298

Symptom

: TI/EI interfaces on interface module are lost as IOMD crashes after a switchover.

Conditions

: This issue occurs after IOMD crashes when a switchover was performed.

Workaround

: There is no workaround.

  •

CSCue52774

Symptom

: Sonet controller as input clock source does not get selected on A900-IMA4OS interface 

module on a Cisco ASR 903 router.

Condition

: This issue occurs when the port above 0 is used for the clock source.

Workaround

: Use port 0 for clock source or insert the SFP in the odd port (protect port) adjacent 

to the actual port using an optical splitter. The cable is fed to the odd port to recover the proper 
clocking for the port.

  •

CSCue52968

Symptom

: Ping failure occurs and traffic stops through Multilink bundle when Challenge 

Handshake Authentication Protocol (CHAP) authentication is enabled.

Conditions

: This issue is seen when Policy Feature Card (PFC) and Control Field Compression 

(ACFC) is configured on the Cisco ASR 903 router.

Workaround

: There is no workaround.

  •

CSCue57670

Symptom

: The active RSP synchronization LED displays the state incorrectly.

Condition

: This issue occurs after a Stateful Switchover (SSO) is performed without any network 

clock configuration.

Workaround

: There is no workaround. This issue is a cosmetic issue.

  •

CSCue59544

Symptom

: The A900-IMA16D generates a storm on closing the backup tunnel.

Condition

: This issue occur after unshutting the tunnel.

Workaround

: There is no workaround.

  •

CSCue66137

Symptom

: The IOMD crashes with CPU hog messages.

Conditions

: This issue occurs with OC-3 interface module and traffic is sent over a multilink bundle 

with packet size greater than 600 byte.

Workaround

: There is no workaround.

  •

CSCue72438

Symptom

: Link goes down with Rev-D I Gigabit interface module.

Conditions

: This issue occurs on the 1 Gigabit Ethernet interface module port.

Workaround

: There is no workaround.

Summary of Contents for ASR 900 Series























































































































































































































































































































Reviews:

No comments