manualshive.com logo in svg

Cisco ASR 900 Series, Release Notes, Page: 96 / 310

Share
Download
Cisco ASR 900 Series Release Notes Download Page 96

 

8

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter  

  Caveats in Cisco IOS XE 3.7S Releases

  •

CSCue73478

Symptom: The standby RSP Sync LED goes to holdover after switchover.

Conditions: This issue occurs in normal working conditions. This is a cosmetic issue. 

Workaround: There is no workaround.

  •

CSCuf35542

Symptom: PFM fails for about fiveminutes after OIR on the master.

Conditions: This issue occurs when OIR is triggered on the master.

Workaround: Wait for 5-6 minutes after the OIR

  •

CSCug05214

Symptom: QOS does not reject policy-map with match EXP and extended num ACL (permit L4).

Conditions: This issue occurs when the policy-map with match exp and L4 ACL is configured and 
applied on main interface.

Workaround: There is no workaround.

  •

CSCug08566

Symptom: Next-hop of a static redistributed route is unexpectedly marked as unreachable. 

Conditions: This issue occurs when redistributing a static route into BGP (in global or VRF table 
(X) ), whose next-hop points to another VRF (Y), the next-hop will be looked up in (X), and thus 
the route may be marked with next-hop unreachable. 

Workaround: Manually set the next-hop to 0 when redistributing using the 

set ip next-hop 

peer-address

 command. 

  •

CSCul01582

Symptom: The PID for the new fan tray is not reflected for 

show inventory

 command output.

Conditions: This issue occurs when the 

show inventory

 command is issued. The fan tray PID does 

not show up for SNMP walk for Entity MIB.

Workaround: There is no workaround.

  •

CSCul50181

Symptom: The router may see unicast traffic not being forwarded out of the Gigabit Ethernet 
interface while multicast traffic is being processed by the router correctly. Pings fail to a directly 
connected neighbour but OSPF would be up.

Conditions: This issue occurs when BDI configs are configured on the Gigabit Ethernet interface. 

Workaround: Reload the router.

Resolved Caveats—Cisco IOS XE Release 3.7(5)S

This section documents the resolved caveats for the Cisco ASR 903 Router in Cisco IOS XE Release 
3.7(5)S.

  •

CSCua20021

Symptom: The 

clear ethernet cfm ais

 command with evc option does not work.

Conditions: This issue occurs when evc name with 

clear ethernet cfm ais

 command is specified.

Workaround: Use the 

service

 option instead. 

Summary of Contents for ASR 900 Series























































































































































































































































































































Reviews:

No comments