Cisco ASR 900 Series Release Notes Download Page 231

Page: 231 / 310

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Caveats in Cisco IOS XE 3.9S Releases

Conditions:

When IMA are configured.

Workaround:

OIR.

•

CSCub33664

Symptoms:

High Delay values seen when using DMM Sesssion on ASR903 post SSO.

Conditions:

Delay values will be higher only after SSO on ASR903.

Workaround:

Remove and reconfigure DMM sessions again post SSO on AR903.

•

CSCub38619

Symptoms:

System crashes when COS value for vlan under an EFP is modified.

Conditions:

This happens only when a prior operator attempt to modify the COS value failed. This

failure can be due to incompatible efp match conditions on the egress efp.

Workaround:

None

•

CSCub41772

Symptom:

Router console is flooded with CPUHOG and EVENTLIB messages.

Conditions:

The issue occurs rarely when you issue multiple interface module reset (OIRs), RSP

switchovers (SSO), or reloads while using a configuration with a high number of T1 serial links on
the OC-3 interface module.

Workaround:

There is no workaround; however, the messages to not affect router functionality.

•

CSCub48129

Symptoms:

CFM CCM’s were being sent out on egress interface with cfm disabled.

Conditions:

Configure UP mep on EVC BD.DIsable cfm on the egress interface.

Workaround:

There is no workaround.

•

CSCub49985

Symptoms:

MPLS pseudowire ping from the peer to the Cisco ASR 903 fails if the peer is using

TTL-based ping.

Conditions:

This symptom occurs when the peer is using TTL-based ping.

Workaround:

There is no workaround.

•

CSCub50110

Symptoms:

Tx timer table not programmed after shut/no shut for hardware offload BFD. It is not

consistently seen.

Conditions:

The issue is seen while we do shut/no shut on BDI/Physical interface which has BFD

configured.

Workaround:

None.

•

CSCub50487

Symptoms:

The router accepts a rewrite push statement on an EFP configured with QinQ

encapsulation.

Conditions:

Occurs when you configure an xconnect EFP with QinQ encapsulation and a rewrite

push statement.

Workaround:

There is no workaround.

•

CSCub52571

Symptoms:

Traceback seen on console. This traceback doesn’t impact any functionality

Summary of Contents for ASR 900 Series























































































































































































































































































































Search results

Summary of Contents for ASR 900 Series

Reviews:

Cisco ASR 900 Series, Release Notes, Page: 231 / 310

Search results

Summary of Contents for ASR 900 Series

Reviews: