manualshive.com logo in svg

Cisco ASR 900 Series, Release Notes, Page: 285 / 310

Share
Download
Cisco ASR 900 Series Release Notes Download Page 285

 

31

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

  Caveats in Cisco IOS XE 3.10S Releases

•

CSCug58606

Symptom:

 When you use the 

no shutdown

 command, the LED of 1G and 10G IM turns off.

Conditions:

 This issue is observed when you use the 

no shutdown

 command on 1G and 10G 

interfaces.

Workaround:

 There is no workaround.

•

CSCug61357

Symptom:

 ISIS adjacency and BFD stay down after using the 

shutdown

 and 

no shutdown 

commands.

Conditions:

 This issue is observed in R-LFA configurations.

Workaround:

 Use the 

shutdown

 and 

no shutdown 

commands again.

•

CSCug83426

Symptom:

 Interface reports loss of frame alarm and goes down.

Conditions:

 This issue is observed when you use the 

shutdown

 and 

no shutdown

 commands on 

the controllers of PE and CE. 

Workaround:

 Perform an OIR on CE side.

•

CSCug83846

Symptom:

 The MTU value does not take effect on an interface.

Conditions:

 This issue is observed when you try to configure more than eight unique MTU values 

on the router.

Workaround:

 There is no workaround.

•

CSCug94540

Symptom:

 The total drop counters on an interface is not displayed when HQoS policy map is 

applied.

Conditions:

 This issue is observed when you apply a two-level policy on a port. 

Workaround:

 Use the 

show policy-map interface gigabitethernet 0/0/0

 command or 

show hqf 

interface gigabitethernet 0/0/0 

command.

•

CSCug96958

Symptom:

 IMA interfaces stay up even when you use the 

shutdown

 command to shut down the 

controller.

Conditions:

 This issue is observed when you use the 

shutdown

 command on the OC3 controller.

Workaround:

 Use the no shutdown command bring up the controller and interfaces. 

•

CSCug99750

Symptom:

 The Cisco ASR 903 router crashes when it accesses unpopulated data structures.

Conditions:

 This issue is observed when you perform an IM OIR and use the 

shutdown

 and 

no 

shutdown

 commands.

Workaround:

 There is no workaround.

•

CSCuh00009

Symptom:

 RSP crashes due to keepalive failure.

Conditions:

 This issue is observed when the router is being polled from different SNMP servers at 

different intervals.

Summary of Contents for ASR 900 Series























































































































































































































































































































Reviews:

No comments