manualshive.com logo in svg

Cisco ASR 900 Series, Release Notes, Page: 261 / 310

Share
Download
Cisco ASR 900 Series Release Notes Download Page 261

 

7

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

  Caveats in Cisco IOS XE 3.10S Releases

•

CSCuj43453

Symptom: IOSd crash was seen on the router on bootup of PTP process.

Conditions: This issue occurs during bootup when multiple reloads of the router is performed.

Workaround: There is no workaround.

•

CSCuj43795

Symptom: The port in error-disabled state & physical status shows as down but is UP on the other 
connected end device.

Conditions: This issue occurs when the port is configured with DHCP rate limiting values so that 
the port goes to error-disable state once it reaches the rate configured.

Workaround: Perform a 

shutdown

 followed by a 

no shutdown

 on the respective interface to move 

the port to UP state.

•

CSCuj60116

Symptom: SYNC-E does not get synced in WAN mode.

Conditions: This issue occurs in WAN mode.

Workaround: There is no workaround.

•

CSCuj60771

Symptom: Self-generated DHCP traffic generating out of the router is not getting marked (cos) with 
user specified value.

Conditions: This issue occurs when DHCP packets (CPU to client) are not getting marked.

Workaround: There is no workaround.

•

CSCuj96689

Symptom: 

Queue-limit

 command is not programmed for priority queue.

Conditions: This issue occurs when the policy map has both BRP and Priority queue with 
queue-limit configured for priority queue.

Workaround: Perform the following;

–

Attach the policy with all BRP configuration. 

–

Dynamically add the 

queue-limit

 command to the priority class.

•

CSCul10279

Symptom: Crash observed on the router with multicast VPN configuration.

Conditions: This issue occurs when the router is configured with multicast VPN IPv4 configuration, 
Scaled ACL and IGMP Static Join configuration.

Workaround: There is no workaround.

•

CSCul11877

Symptom: HSRP standby router cannot ping the virtual IP.

Conditions: This issue occurs when the BDI interfaces are configured along with a range of bridge 
domains.

Workaround: There is no workaround.

•

CSCul21294

Symptom: PTSF alarms do not get posted when the egress interface is shutdown.

Conditions: This issue occurs when a PTP slave has one or more masters.

Summary of Contents for ASR 900 Series























































































































































































































































































































Reviews:

No comments