manualshive.com logo in svg

Cisco ASR 900 Series, Release Notes, Page: 107 / 310

Share
Download
Cisco ASR 900 Series Release Notes Download Page 107

 

19

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter 

  Caveats in Cisco IOS XE 3.7S Releases

  •

CSCug55586

Symptom:

 If you dynamically remove the egress markings, ingress marking does not work.

Conditions:

 This issue is observed if a marking is present at the logical level in the egress direction, 

DM does not work.

Workaround:

 Use the egress set at leaf or PHB level. 

  •

CSCug67955

Symptom:

 The standby FP is stuck in init state.

Conditions:

 This issue occurs after ISSU is performed.

Workaround:

 There is no workaround.

  •

CSCug72785

Symptom:

 OSPF flap observed on the router.

Conditions:

 This issue occurs after IM OIR followed by SSO.

Workaround:

 There is no workaround.

  •

CSCug73776

Symptom:

 The standby router crashes on bootup when highly scaled configurations and when 

L2VPN and multicast are configured.

Conditions:

 This issue occurs on reloading the router 3-4 times with highly scaled configurations 

and L2VPN and multicast are configured.

Workaround:

 There is no workaround.

  •

CSCug83846

Symptom:

 The MTU value does not take effect on an interface.

Conditions: 

This issue is observed when you try to configure more than eight unique MTU values 

on the router.

Workaround:

 There is no workaround. 

  •

CSCug86963

Symptom:

 Bidirectional Forwarding Detection (BFD) is unable to resolve neighbor Address 

Resolution Protocol (ARP).

Conditions:

 This issue occurs when software BFD is configured with static client; and IM OIR or 

reload is performed.

Workaround:

 Use manual ping. 

  •

CSCug91295

Symptom:

 UDP based ACLs do not work after a router reload.

Conditions:

 This issue occurs after reload.

Workaround:

 Remove and add the ACL.

  •

CSCug97639

Symptom:

 IPv4 VRF ping fails when disabling IPv6 unicast-routing globally.

Conditions:

 This issue occurs when IPv6 unicast-routing is disabled.

Workaround:

 Enable IPv6 unicast-routing 

Summary of Contents for ASR 900 Series























































































































































































































































































































Reviews:

No comments