Cisco ASR 900 Series Release Notes Download Page 83

Page: 83 / 310

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter Restrictions and Caveats in Cisco IOS XE 3.6S Releases

Caveats in Cisco IOS XE 3.6S Releases

–

You set the MTU to a higher value on an MLP bundle.

Workaround

: There is no workaround.

•

CSCty61660

Symptoms:

The Cisco ASR 903 Router displays a core dump file.

Conditions:

Occurs when the remote PE device is reloaded while running VPLS-TP.

Workaround:

There is no workaround.

•

CSCty66871

Symptoms:

The router stops forwarding traffic across one or more EoMPLS virtual circuits (VC)s

Conditions:

Occurs when you perform a shut/no shutdown on the MPLS TE tunnel carrying the VC.

Workaround:

Issue the clear xconnect command on the VC.

•

CSCty70034

Symptoms:

The router floods all EFPs in the sam e split horizon group with IGMP join messages.

Conditions:

Occurs when the router is sending an IGMP join containing a dot1q tag for one EVC.

Workaround:

None.

•

CSCty72251

Symptoms:

The router drops traffic following a reload.

Conditions

: Occurs when you reload the router while running a VRF configuration.

Workaround

: Remove the configuration, reload the router, and re-apply the configuration.

•

CSCty72901

Symptoms:

Some CEM groups do not function correctly.

Conditions

: Occurs when you configure more than 196 CEM groups on the T1/E1 or OC-3 interface

module.

Workaround

: There is no workaround; avoid configuring more than 196 CEM groups.

•

CSCty73142

Symptoms:

An IPC Init failure occurs during downgrade, which makes the standby reload

continuously.

Conditions

: Occurs when you perform an ISSU downgrade from IOS XE 3.6 to IOS XE 3.5.1 or 3.5.

Workaround

: There is no workaround.

•

CSCty73362

Symptoms:

The router experiences CPP download failures when sending IGMP join messages.

Conditions:

Occurs when the router is configured with a trunk EFP in SM mode on the access side

and is sending IGMP join messages to more than 1970 multicast groups.

Workaround:

There is no workaround.

•

CSCty73365

Symptoms:

The router drops traffic on ATM subinterfaces using layer 2 PVCs.

Conditions:

Occurs when you create 255 or more ATM PVCs.

Workaround:

There is no workaround.

Summary of Contents for ASR 900 Series























































































































































































































































































































Search results

Summary of Contents for ASR 900 Series

Reviews:

Cisco ASR 900 Series, Release Notes, Page: 83 / 310

Search results

Summary of Contents for ASR 900 Series

Reviews: