manualshive.com logo in svg

Cisco ASR 900 Series, Release Notes, Page: 273 / 310

Share
Download
Cisco ASR 900 Series Release Notes Download Page 273

 

19

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

  Caveats in Cisco IOS XE 3.10S Releases

Symptom: 

Although a QoS policy is configured, PTP packets are treated as default packets.

Conditions:

 This issue is observed when the CPU-generated PTP packets do not reach egress QoS 

with high a priority label (15 or 126).

Workaround:

 There is no workaround.

•

CSCuh85041

Symptom: 

SNMP returns the wrong card type for the serial interface module.

Conditions:

 Issue occurs during SNMP walk of ASR903.

Workaround:

 There is no workaround. This issue is not service affecting.

•

CSCuh85990

Symptom:

 When you use the 

show ethernet cfm maintenance-points remote

 command, only 992 

remote maintenance endpoints are displayed.

Conditions:

 This issue is observed when you configure CFM MEP domains on an EVC.

Workaround:

 There is no workaround.

•

CSCuh88500

Symptom:

 Standby router reloads due to SPA bulk synchronization failure.

Conditions:

 This issue is observed when you perform an SSO.

Workaround:

 There is no workaround.

•

CSCui06748

Symptom:

 ICMP packets are punted to the CPU even after using the 

no ip redirect

 command on 

the Cisco ASR 903 router. 

Conditions:

 This issue is observed when ICMP packets are punted initially.

Workaround:

 There is no workaround.

•

CSCui14481

Symptom:

 Traffic does not flow for HSPW sessions as the tunnel ID is incorrect.

Conditions:

 This issue is observed when you perform an IM OIR.

Workaround:

 Perform an SSO and flap the access interface.

•

CSCui19632

Symptom:

 BFD sessions flap randomly.

Conditions:

 This issue is observed in FPGA version 30020.

Workaround:

 There is no workaround.

•

CSCui19700

Symptom:

 When you apply a QoS policy on the core interface, QoS counters do not increment.

Conditions:

 This issue is observed when you apply a policy on the access interface with 500 EFPs 

and apply another policy on the core interface.

Workaround:

 There is no workaround.

•

CSCui22637

Symptom:

 The Cisco ASR 903 router crashes.

Conditions:

 This issue is observed when you unconfigure 1000 Ethernet service instances.

Workaround:

 There is no workaround.

Summary of Contents for ASR 900 Series























































































































































































































































































































Reviews:

No comments