manualshive.com logo in svg

Cisco ASR 900 Series, Release Notes, Page: 294 / 310

Share
Download
Cisco ASR 900 Series Release Notes Download Page 294

 

6

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

  Caveats in Cisco IOS XE 3.11S Releases

Workaround:

 Manually resolve ARP by pinging the next hops BDI interface. 

•

CSCug44762

Symptom:

 POS interface stays down after a 

shutdown

 followed by a 

no shutdown

 on POS 

interface.

Conditions:

 This issue is seen when a 

shutdown

 followed by a 

no shutdown

 is performed on POS 

interface.

Workaround:

 Perform 

shutdown

 followed by a 

no shutdown 

on the controller.

•

CSCug50283

Symptom:

 Only 2-path are utilized for load sharing though 3-path is available.

Conditions:

 This issue occurs when ECMP is configured.

Workaround:

 There is no workaround.

•

CSCug61505

Symptom:

 The 

platform enable

 command is seen for ACR virtual controller when OC-3 IM is 

present in slot 0.

Conditions:

 This issue occurs after configuring 

aps group acr

 command on the OC-3 controller.

Workaround:

 Insert the IM in other bays instead of bay 0.

•

CSCug83434

Symptom:

 Lot of memory leak chunks are seen for FMANRP on the standby RSP.

Conditions:

 This issue occurs after memory leaks are verified on standby RSP.

Workaround:

 Perform a router reload. 

•

CSCug84082

Symptom:

 ATM/IMA PVP links configured on either T1/E1 IM or OC-3IM exhibit traffic or ping 

failure.

Conditions:

 This issue occurs when ATM/IMA link flaps and is followed by SSO. Link flap can be 

IM OIR, etc.

Workaround:

 Performing an IM OIR may fix the issue, else perform a router reload.

•

CSCug84428

Symptom:

 Traffic drop are seen on the T1/E1 IM serial and MLPPP links.

Conditions:

 This issue occurs when traffic is sent via streams with jumbo packet sizes of 7000 bytes 

or larger. The interfaces toggle between the up/down state.

Workaround:

 Perform a IM OIR of the T1/E1 IM. 

•

CSCug89348

Symptom:

 IOSXE_RP_SPA-3-IPCPORTFAIL tracebacks are seen on router with high availability 

configured.

Conditions:

 This issue occurs after SSO is performed.

Workaround:

 There is no workaround.

•

CSCug92536

Symptom:

 PLATFORM-3-NOMAC traceback is seen on standby console.

Conditions:

 This issue is seen when CEM-ACR is configured on a HA setup.

Workaround:

 There is no workaround. 

Summary of Contents for ASR 900 Series























































































































































































































































































































Reviews:

No comments