manualshive.com logo in svg

Cisco ASR 900 Series, Release Notes, Page: 59 / 310

Share
Download
Cisco ASR 900 Series Release Notes Download Page 59

C H A P T E R

 

1

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

9

Restrictions and Caveats in Cisco IOS XE 3.6S 
Releases

This chapter provides information about restrictions and caveats in Cisco IOS XE 3.6S releases.

Note

Because Cisco IOS XE 36S is based on Cisco IOS XE 3.5 inherited releases, some caveats that apply to 
Cisco IOS XE 3.5 releases also apply to Cisco IOS XE 36S. Release 3.5 is not described in this 
document; for a list of the software caveats that apply to Cisco IOS XE 3.5, see the 

Release Notes for 

Cisco IOS XE Release 3S

. 

Note

We recommend that you view the field notices for the current release to determine whether your software 
or hardware platforms are affected. You can access field notices at 

http://www.cisco.com/en/US/support/tsd_products_field_notice_summary.html.

This chapter contains the following sections:

•

Limitations and Restrictions, page 9-1

•

Caveats in Cisco IOS XE 3.6S Releases, page 9-6

Limitations and Restrictions

The following sections describe the Cisco ASR 903 Router limitations:

•

Limitations and Restrictions in Cisco IOS XE Release 3.6(2)S, page 9-1

•

Limitations and Restrictions in Cisco IOS XE Release 3.6(1)S, page 9-2

•

Limitations and Restrictions in Cisco IOS XE Release 3.6S, page 9-4

Limitations and Restrictions in Cisco IOS XE Release 3.6(2)S

Note

For a summary of limitations in Release 3.5S, see the 

IOS XE 3.5 Release Notes

. 

Summary of Contents for ASR 900 Series























































































































































































































































































































Reviews:

No comments