Cisco ASR 900 Series Release Notes Download Page 162

Page: 162 / 310

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

Caveats in Cisco IOS XE 3.8S Releases

Symptom:

CPU utilization is high after executing the show mac-address-table command.

Conditions:

This issue occurs after scaled MAC entries are learned over the BD.

Workaround:

Execute the command with reduced term length.

•

CSCue40248

Symptom:

Traffic does not flow through newly created MLP interfaces after a switchover is

performed.

Conditions:

This issue occurs after you have a newly created MLP interface terminated under a

VRF and a switchover is performed.

Workaround:

There is no workaround.

•

CSCue43036

Symptom:

%IDBINDEX_SYNC-4-RESERVE traceback seen on OC-12 card type.

Conditions:

This issue occurs after the card type is set the to OC-12 and the router is reloaded. This

issue is seen on a HA system with POS configuration.

Workaround:

There is no workaround.

•

CSCue51682

Symptom:

The REP protocol flaps, as indicated by the following error messages:

*Feb 8 06:51:38.857: %REP-4-LINKSTATUS: GigabitEthernet0/0/1 (segment 10) is

non-operational due to neighbor not responding

*Feb 8 06:51:39.096: %REP-4-LINKSTATUS: GigabitEthernet0/0/1 (segment 10) is

operational

Conditions:

This issue occurs with REP fast LSL (with lsl-ageout 200msec) is configured and when

a burst of new MAC address (usually > 4k) is getting learnt into the system.

Workaround:

Remove fast LSL from the REP configuration

•

CSCue54997

Symptom:

Two input clock sources are accepted from same OC-3 IM but the system can support

only one input clock source per OC-3 IM.

Conditions:

This issue occurs when two input clock sources are getting accepted from same OC-3

IM.

Workaround:

There is no workaround. Do not configure the second input clock source from same

OC-3 IM or remove both OC-3 IM sources and exit the configuration and configure the desired OC-3
IM controller alone.

•

CSCue75372

Symptom:

TIME-HOG messages are seen during an IM OIR.

Condition:

This issue occurs when default and IP template is used.

Workaround:

There is no workaround.

•

CSCue96886

Symptoms:

Complete MAC Address space is not available on the RSP.

Conditions:

This issue occurs after removing the service instance with the MAC Addresses learnt

on the BD.

Workaround:

Reload the Router.

•

CSCuf15768

Summary of Contents for ASR 900 Series























































































































































































































































































































Search results

Summary of Contents for ASR 900 Series

Reviews:

Cisco ASR 900 Series, Release Notes, Page: 162 / 310

Search results

Summary of Contents for ASR 900 Series

Reviews: