Cisco ASR 900 Series Release Notes Download Page 105

Page: 105 / 310

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

Caveats in Cisco IOS XE 3.7S Releases

•

CSCuf53527

Symptom:

Cos inner value gets copied into the cos value.

Conditions:

This issue occurs when QinQ without rewrite service instance is configured.

Workaround:

Apply the qos policy-map to the cos inner value.

•

CSCuf56723

Symptom:

The interface LED glows green when shut.

Conditions:

This issue occurs after an SSO is performed.

Workaround:

There is no workaround.

•

CSCuf65301

Symptom:

Micro flaps observed on the router.

Conditions:

This issue is seen when system is kept idle for hours.

Workaround:

There is no workaround

•

CSCuf79397

Symptom:

F1 is stuck in init state after the standby RSP reloads.

Conditions:

This issue occurs on a reload or OIR of the standby RSP.

Workaround:

Reload the standby RSP again.

•

CSCuf83886

Symptom:

Label exhaust message is seen even on valid case if policy is configured before xconnect

is configured on scaled configuration.

Conditions:

This issue occurs when a service-policy is configured before configuring xconnect on

the router that has consumed close to max labels.

Workaround:

First configure xconnect and then configure service-policy.

•

CSCug05239

Symptom:

Traffic drops on the router.

Conditions:

This issue occurs when configuring multichassis Link Aggregation Control Protocol

(MLACP) switchover with Ethernet over Multiprotocol Label Switching (EOMPLS).

Workaround:

Configure port channel with EOMPLS.

•

CSCug05647

Symptom:

Interface counters do not get updated with IP traffic.

Conditions:

This issue occurs when pinging back to back connected interfaces; the interface

counters stay at 0.

Workaround:

Reload the device

•

CSCug18630

Symptom:

When you perform an OIR on the standby and active RSPs, CMAND crashes.

Conditions:

This issue is observed after performing multiple standby OIRs and bringing the

standby machine up.

Workaround:

There is no workaround.

Summary of Contents for ASR 900 Series























































































































































































































































































































Search results

Summary of Contents for ASR 900 Series

Reviews:

Cisco ASR 900 Series, Release Notes, Page: 105 / 310

Search results

Summary of Contents for ASR 900 Series

Reviews: