manualshive.com logo in svg

Cisco ASR 900 Series, Release Notes, Page: 33 / 310

Share
Download
Cisco ASR 900 Series Release Notes Download Page 33

 

5

Cisco IOS XE 3S Release Notes for the Cisco ASR 903 Router

OL-26630-12

Chapter

  New Software Features in Cisco IOS XE Release 3.8(0)S

interface port-channel 4

 service instance 1 ethernet

  encapsulation untagged

  l2protocol peer lacp

  bridge-domain 1

 !

 service instance trunk 10 ethernet

  encapsulation dot1q <>

  rewrite ingress tag pop 1 symmetric

  bridge-domain from-encapsulation

!

For more information about configuring EFP interfaces, see the 

Configuring Ethernet Virtual 

Connections on the Cisco ASR 903 Router

.

•

Y.1731 enhancements—This release introduces support for Y.1731 on-demand and concurrent 
features. For more information about this feature, see 

http://www.cisco.com/en/US/partner/docs/ios-xml/ios/cether/configuration/xe-3s/asr903/ce-y1731
-perfmon.html

Summary of Contents for ASR 900 Series























































































































































































































































































































Reviews:

No comments