Canon imageRUNNER ADVANCE C5500 Series, Service Manual, Page: 563 / 1331

5F0-8002-02 Error in the Saddle Paper End Stopper Motor (Finisher-Y1)
Detection Description The Saddle Paper End Stopper HP Sensor does not detect the saddle paper end stopper when
the Saddle Paper End Stopper Motor has been driven for 4 seconds.
Remedy
STAPLE FIN-Y1/BOOKLET FIN-Y1
[Related parts]
- Harnesses from the Saddle Paper End Stopper HP Sensor (PS210) to the Saddle Stitcher
Controller PCB
- Harnesses from the Saddle Paper End Stopper Motor (M206) to the Saddle Stitcher Controller
PCB
- Saddle Paper End Stopper HP Sensor (PS210)
- Saddle Paper End Stopper Motor (M206)
- Saddle Stitcher Controller PCB (PCB201)
- Finisher Controller PCB (PCB101)
[Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection
timing of this error, this error code may be displayed. Accordingly, perform the following work before
checking the related parts.
1. Check whether there is not the mulfunction in the swing guide unit.
2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102).
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
5F1-8003-02 Saddle Delivery Motor clock error (Finisher-Y1)
Detection Description The lock state of Saddle Delivery Motor is detected 0.2 seconds or more while the motor operates.
Remedy STAPLE FIN-Y1/BOOKLET FIN-Y1
[Related parts]
- Harnesses from the Saddle Delivery Motor Clock Sensor (PS211) to the Saddle Stitcher
Controller PCB
- Harnesses from the Saddle Delivery Motor (M207) to the Saddle Stitcher Controller PCB
- Saddle Delivery Motor Clock Sensor (PS211)
- Saddle Delivery Motor (M207)
- Saddle Stitcher Controller PCB (PCB201)
- Finisher Controller PCB (PCB101)
[Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection
timing of this error, this error code may be displayed. Accordingly, perform the following work before
checking the related parts.
1. Check whether there is not the mulfunction in the swing guide unit.
2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102).
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
5F3-8001-02 Error in the Saddle Alignment Motor (Finisher-Y1)
Detection Description The saddle alignment plate does not come off the Saddle Alignment HP Sensor when the Saddle
Alignment Motor has been driven for 1 second.
Remedy STAPLE FIN-Y1/BOOKLET FIN-Y1
[Related parts]
- Harnesses from the Saddle Alignment HP Sensor (PS207) to the Saddle Stitcher Controller PCB
- Harnesses from the Saddle Alignment Motor (M203) to the Saddle Stitcher Controller PCB
- Saddle Alignment HP Sensor (PS207)
- Saddle Alignment Motor (M203)
- Saddle Stitcher Controller PCB (PCB201)
- Finisher Controller PCB (PCB101)
[Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection
timing of this error, this error code may be displayed. Accordingly, perform the following work before
checking the related parts.
1. Check whether there is not the mulfunction in the swing guide unit.
2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102).
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
7. Error/Jam/Alarm
549