Canon imageRUNNER ADVANCE C5500 Series, Service Manual, Page: 556 / 1331

577-8001-02 a. Paddle Motor error (Finisher-H1) b. Error in the Saddle Feed/Paddle Motor (Finisher-Y1)
Detection Description a. The Return Belt HP Sensor was not turned ON although 1 second had passed after the Paddle
Motor operation started. The last paddle operation is not finished when driving the Paddle Motor.
b. The paddle does not come off the Saddle Paddle HP Sensor when the Saddle Feed/Paddle
Motor has been driven for 1 second.
Remedy
a. INNER FIN-H1
[Related parts]
- Harnesses and connectors from the Finisher Controller PCB to the Return Belt HP Sensor
- Harnesses and connectors from the Finisher Controller PCB to the Paddle Motor
- Return Belt HP Sensor (PS3)
- Paddle Motor (M10)
- Finisher Controller PCB (PCB1)
b.STAPLE FIN-Y1/BOOKLET FIN-Y1
[Related parts]
- Harnesses from the Saddle Paddle HP Sensor (PS206) to the Saddle Stitcher Controller PCB
- Harnesses from the Saddle Feed/Paddle Motor (M201) to the Saddle Stitcher Controller PCB
- Saddle Paddle HP Sensor (PS206)
- Saddle Feed/Paddle Motor (M201)
- Saddle Stitcher Controller PCB (PCB201)
- Finisher Controller PCB (PCB101)
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
577-8002-02 Error in the Saddle Feed/Paddle Motor (Finisher-Y1)
Detection Description The Saddle Paddle HP Sensor does not detect the paddle when the Saddle Feed/Paddle Motor
has been driven for 1 second.
Remedy STAPLE FIN-Y1/BOOKLET FIN-Y1
[Related parts]
- Harnesses from the Saddle Paddle HP Sensor (PS206) to the Saddle Stitcher Controller PCB
- Harnesses from the Saddle Feed/Paddle Motor (M201) to the Saddle Stitcher Controller PCB
- Saddle Paddle HP Sensor (PS206)
- Saddle Feed/Paddle Motor (M201)
- Saddle Stitcher Controller PCB (PCB201)
- Finisher Controller PCB (PCB101)
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
578-8001-02 Error in the Return Roller Lift Motor (Finisher-Y1)
Detection Description The return roller does not come off the Return Roller HP Sensor when the Return Roller Lift Motor
has been driven for 1 second.
Remedy STAPLE FIN-Y1/BOOKLET FIN-Y1
[Related parts]
- Harnesses from the Return Roller HP Sensor (PS121) to the Finisher Controller PCB
- Harnesses from the Return Roller Lift Motor (M111) to the Finisher Controller PCB
- Return Roller HP Sensor (PS121)
- Return Roller Lift Motor (M111)
- Finisher Controller PCB (PCB101)
[Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection
timing of this error, this error code may be displayed. Accordingly, perform the following work before
checking the related parts.
1. Check whether there is not the mulfunction in the swing guide unit.
2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102).
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
7. Error/Jam/Alarm
542