Canon imageRUNNER ADVANCE C5500 Series, Service Manual, Page: 552 / 1331

540-8002-02 a. Tray Shift Motor error (Finisher-H1) b. Stack tray area error (Finisher-Y1)
Detection Description a. The Front Alignment Plate HP Sensor was not turned OFF or the Stack Tray Lower Limit Sensor
was not turned ON although 3.5 seconds had passed after the Front Alignment Motor operation
started in the tray down operation.
The Front Alignment Plate HP Sensor was not turned OFF after the tray was moved down in the
paper level detection operation.
b. The stack tray detects the discontinuous area during the operation.
Remedy
a. INNER FIN-H1
[Related parts]
- Harnesses and connectors from the Finisher Controller PCB to the Stack Tray Paper Height
Sensor
- Harnesses and connectors from the Finisher Controller PCB to the Tray Shift Motor
- Stack Tray Paper Height Sensor (PS9)
- Tray Shift Motor (M6)
- Finisher Controller PCB (PCB1)
b.STAPLE FIN-Y1/BOOKLET FIN-Y1
[Related parts]
- Harnesses from the Stack Tray HP Sensor (PS106) to the Finisher Controller PCB
- Harnesses from the Stack Tray Full Sensor 1/2/3 (PS107/PS108/PS109) to the Finisher
Controller PCB
- Harnesses from the Stack Tray Upper Limit Sensor (PS110) to the Finisher Controller PCB
- Harnesses from the Stack Tray Shift Motor (M105) to the Finisher Controller PCB
- Stack Tray HP Sensor (PS106)
- Stack Tray Full Sensor 1/2/3 (PS107/PS108/PS109)
- Stack Tray Shift Motor (M105)
- Finisher Controller PCB (PCB1)
[Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection
timing of this error, this error code may be displayed. Accordingly, perform the following work before
checking the related parts.
1. Check whether there is not the mulfunction in the swing guide unit.
2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102).
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
540-8004-02 Stack tray paper surface detection error (Finisher-Y1)
Detection Description The Stack Tray Paper Surface Sensor does not turn off when the stack tray has been lowered for
10 seconds.
Remedy STAPLE FIN-Y1/BOOKLET FIN-Y1
[Related parts]
- Harnesses from the Stack Tray Paper Surface Sensor (light-emitting) (PBA101) to the Finisher
Controller PCB
- Harnesses from the Stack Tray Paper Surface Sensor (light-receiving) (PBA102/PBA103) to the
Finisher Controller PCB
- Harnesses from the Stack Tray Shift Motor (M105) to the Finisher Controller PCB
- Stack Tray Paper Surface Sensor (light-emitting) (PBA101)
- Stack Tray Paper Surface Sensor (light-receiving) (PBA102/PBA103)
- Stack Tray Shift Motor (M105)
- Finisher Controller PCB (PCB101)
[Points to note at work] When the Swing Guide Safety Switch (SW102) turns on at the detection
timing of this error, this error code may be displayed. Accordingly, perform the following work before
checking the related parts.
1. Check whether there is not the mulfunction in the swing guide unit.
2. Check whether there is not the mulfunction in the Swing Guide Safety Switch (SW102).
[Remedy] Check/replace the related harness/cable, connector and parts.
[Reference] When replacing the Finisher Controller PCB, refer to "Adjustment> When Replacing
the Parts" in the Service Manual.
7. Error/Jam/Alarm
538