Buffalo LinkStation LS-CHL User Manual Download Page 199

Page: 199 / 214

LinkStation User Manual

198

Appendix

The Info/Error LED blinks red to indicate an error.

The error may be identified by the pattern of blinking.

Note:

The error may also be viewed from NAS Navigator2.

Error code Descriptions

E04

The firmware is corrupted. Contact Buffalo technical support for assistance.

E10

The LinkStation is running on the UPS battery due to a power outage. The system

will now be shut down safely. Check that power is being supplied to the UPS, and if

there are no problems, turn on the LinkStation.

E11

An error occurred in the fan speed. Check that no foreign objects or dust are

clogging the fan. If any foreign objects or dust are found, use a pair of tweezers, air

duster, or other tool to remove them.

If the error is displayed again, contact Buffalo technical support for assistance.

E12

System temperature has exceeded the maximum safe value. Do not place objects in

the area around the LinkStation.

Also, move the LinkStation to a cooler location.

E13

An error occurred in the RAID array. It will run in degraded mode until the error is

corrected. Replace the failed drive indicated by the red LED as soon as possible. After

replacement, rebuild the RAID array after starting the LinkStation.

E14

The RAID array cannot be mounted. Run the RAID array disk check in the

LinkStation's Web Admin interface.

E15

The bad sectors in the hard drive have reached a dangerous level. Replace the hard

drive indicated by the red LED.

E16

Unable to find the hard drive. The drive may be disconnected or may have failed.

After shutting down, reinstall the hard drive.

E22

Mounting of hard drive failed. Format the hard drive. After formatting and rebooting,

if the error still appears, replace the drive.

If this error is displayed again, contact Buffalo technical support for assistance.

E23

An error occurred, so the hard drive was removed from the RAID array. Replace the

hard drive indicated by the red LED.

E30

The hard drive may be damaged. Replace the hard drive indicated by the red LED.

Place

Status

10s place

The LED illuminates for 1.0 second every 0.3 seconds.

The number of flashes is the tens place of the error code.

1s place

The LED illuminates for 0.5 seconds every 0.3 seconds.

The number of flashes is the ones place of the error code.

Summary of Contents for LinkStation LS-CHL























































































































































































































Search results

Summary of Contents for LinkStation LS-CHL

Reviews:

Related manuals for LinkStation LS-CHL

Brands by name

Popular brands

Buffalo LinkStation LS-CHL, User Manual

Search results

Summary of Contents for LinkStation LS-CHL

Reviews:

Related manuals for LinkStation LS-CHL

Brands by name

Popular brands