Broadcom NetXtreme II SERIES User Manual Download Page 252

Page: 252 / 264

Regulatory Information: Broadcom NetXtreme II® Network Adapter User Guide

file:///C|/Users/Nalina_N_S/Documents/NetXtremeII/English/regs.htm[9/5/2014 3:45:21 PM]

Canadian Regulatory Information (Canada Only)

Industry Canada, Class A

Broadcom NetXtreme II Gigabit Ethernet Controller

BCM95709SA0908G

Broadcom NetXtreme II 10 Gigabit Ethernet Controller

BCM957710A1023G
BCM957711A1123G (E03D001)
E02D001

Dell Inc.
Worldwide Regulatory Compliance, Engineering and Environmental Affairs
One Dell Way PS4-30
Round Rock, Texas 78682, USA
512-338-4400

This Class A digital apparatus complies with Canadian ICES-003.

Notice

: The Industry Canada regulations provide that changes or modifications not expressly approved by Dell Inc. could void

your authority to operate this equipment.

Industry Canada, classe A

Broadcom NetXtreme II Gigabit Ethernet Controller

BCM95709SA0908G

Broadcom NetXtreme II 10 Gigabit Ethernet Controller

BCM957710A1023G

Summary of Contents for NetXtreme II SERIES









































































































































































































































































Search results

Summary of Contents for NetXtreme II SERIES

Reviews:

Related manuals for NetXtreme II SERIES

Brands by name

Popular brands

Broadcom NetXtreme II SERIES, User Manual

Search results

Summary of Contents for NetXtreme II SERIES

Reviews:

Related manuals for NetXtreme II SERIES

Brands by name

Popular brands