Broadcom NetXtreme II SERIES User Manual Download Page 150

Page: 150 / 264

Fibre Channel Over Ethernet: Broadcom NetXtreme II® Network Adapter User Guide

file:///C|/Users/Nalina_N_S/Documents/NetXtremeII/English/fcoe.htm[9/5/2014 3:45:12 PM]

6. For each interface to be enabled for FCoE boot, click

Change Settings

and ensure

FCoE Enable

and

AUTO_VLAN

are set to

yes

and

DCB required

is set to

7. For each interface to be enabled for FCoE boot, click on

Create FCoE VLAN Interface

. The VLAN interface creation dialog will launch. Click

Yes

to confirm. This will trigger

automatic FIP VLAN discovery. If successful, the VLAN will be displayed under

FCoE VLAN Interface

. If no VLAN is visible, check your connectivity and switch configuration.

8. Once complete with configuration of all interface, click

to proceed.

Summary of Contents for NetXtreme II SERIES









































































































































































































































































Search results

Summary of Contents for NetXtreme II SERIES

Reviews:

Related manuals for NetXtreme II SERIES

Brands by name

Popular brands

Broadcom NetXtreme II SERIES, User Manual

Search results

Summary of Contents for NetXtreme II SERIES

Reviews:

Related manuals for NetXtreme II SERIES

Brands by name

Popular brands