Broadcom NetXtreme II SERIES User Manual Download Page 147

Page: 147 / 264

Fibre Channel Over Ethernet: Broadcom NetXtreme II® Network Adapter User Guide

file:///C|/Users/Nalina_N_S/Documents/NetXtremeII/English/fcoe.htm[9/5/2014 3:45:12 PM]

SLES11 SP2 Installation
RHEL6 Installation

SLES11 SP2 Installation

1. Boot from the SLES11 SP2 installation medium and on the installation splash screen press

for driver update disk. Select

Yes

. In boot options, type

withfcoe=1

. Select

Installation

to proceed.

2. Follow the on screen instructions to choose the Driver Update medium and load drivers.

Summary of Contents for NetXtreme II SERIES









































































































































































































































































Search results

Summary of Contents for NetXtreme II SERIES

Reviews:

Related manuals for NetXtreme II SERIES

Brands by name

Popular brands

Broadcom NetXtreme II SERIES, User Manual

Search results

Summary of Contents for NetXtreme II SERIES

Reviews:

Related manuals for NetXtreme II SERIES

Brands by name

Popular brands