Broadcom NetXtreme II SERIES User Manual Download Page 212

Page: 212 / 264

Using Broadcom Advanced Control Suite 4: Broadcom NetXtreme II® Network Adapter User Guide

file:///C|/Users/Nalina_N_S/Documents/NetXtremeII/English/bacs.htm[9/5/2014 3:45:16 PM]

16. Type the VLAN name and then click

Next

NOTE: The team name cannot exceed 39 characters, cannot begin with spaces, and cannot contain any of the following

characters: & \ / : * ? < > |

17. To tag the VLAN, select

Tagged

and then click

Next

. Otherwise, click

Untagged

, click

Next

, and continue with the wizard to

Summary of Contents for NetXtreme II SERIES









































































































































































































































































Search results

Summary of Contents for NetXtreme II SERIES

Reviews:

Related manuals for NetXtreme II SERIES

Brands by name

Popular brands

Broadcom NetXtreme II SERIES, User Manual

Search results

Summary of Contents for NetXtreme II SERIES

Reviews:

Related manuals for NetXtreme II SERIES

Brands by name

Popular brands