Bosch B465 Installation And Operation Manual Download Page 81

Page: 81 / 115

Conettix Universal Dual Path Communicator

Maintenance and troubleshooting | en

Bosch Security Systems, Inc.

Installation and Operation Manual

2017.11 | 05 | F.01U.311.207

Flash pattern

Function

Flashing

No data received on Phone line 1/Phone line 2.

Flashing

Data error on Phone line 1/Phone line 2.

Off

Phone line 1/Phone line 2 ON-HOOK.

Tab.

11.6:

Phone line 1 and 2 LED descriptions

Conettix Plug-in cellular module LEDs

LED

Function

Blue

Indicates the overall status of the device.

Red

Indicates an unacceptable signal strength level.

Yellow

Indicates a marginal signal strength level.

Green (1 light)*

Indicates a good signal strength level.

Green (2 lights)

Indicates a very good signal strength level.

* One green LED indicates the minimum installation level.

Tab.

11.7:

Cellular module signal strength LED patterns

A single blue Status LED indicates the module status.

Summary of Contents for B465




















































































































Search results

Summary of Contents for B465

Reviews:

Related manuals for B465

Brands by name

Popular brands

Bosch B465, Installation And Operation Manual

Search results

Summary of Contents for B465

Reviews:

Related manuals for B465

Brands by name

Popular brands