Bosch B465 Installation And Operation Manual Download Page 11

Page: 11 / 115

Conettix Universal Dual Path Communicator

System overview | en

Bosch Security Systems, Inc.

Installation and Operation Manual

2017.11 | 05 | F.01U.311.207

–

Pulse 4/2 (1400 Hz ACK Tone)

–

SIA (SIA8, SIA20)

The B465 links the control panel’s PSTN dialer to the internet and then to one of the Bosch
Conettix receivers. The B465:
–

Connects with the control panel PSTN dialer (through the B465 panel line terminals) or
the control panel relay outputs connected to the B465 inputs.

–

Embeds alarm reports in Conettix IP reports and sends them to a Conettix D6600, D6100i
or D6100IPv6 Communications Receiver/Gateway through an IP network.

–

The Conettix receiver replies to the B465 with an acknowledgement report.

–

The B465 sends an acknowledgement back to the control panel through the PSTN
interface which completes the signal transmission

Refer to the following illustration for component locations on the B465.

MPR

BAT

EXT

MODULE 1

MODULE

RELEASE

1 COM 2

3 COM 4

T R
PNL LINE 1

C NO

OUTPUT 2

+ BAT -

- +

NO C NC

OUTPUT 1

TRBL

PANEL
LINE 2

USB

ETHERNET

100BASE-T

LINK

COMMUNICATION MODULE 1

3 COM 4

1 COM 2

R Y G

SDI2

Device Bus

24 VDC

16.5VAC

BATTERY

PANEL
LINE 1

BATTERY

SYSTEM TROUBLE

INPUTS

2.2 k End of

Line Resistors

C NO

OUTPUT 3

12V

AUX COM

T R
PNL LINE 2

16.5VAC

Figure

3.2: Module overview

Call out - description

- Plug-in stabilizing holes (X,Y) - the plug-in cellular communicator modules compatible

with the B465 use the X hole.

- Plug-in module connector - for compatible plug-in cellular communicator modules.

- Plug-in module retention clip - pull the tab towards you to install or release plug-in

cellular communicator modules.

- On-board Ethernet connector - for wired IP communication with D6600 or D6100IPv6

central station receiver.

- USB connector - for temporary connection to a computer for B465 configuration, status,

and diagnotics.

- Status LEDs (SYSTEM TROUBLE, TX, RX, POWER, BATTERY) - these LEDs show system

troubles, Ethernet transmit (TX) and receive (RX) traffic, and the status of the primary power
source and the battery.

Summary of Contents for B465




















































































































Search results

Summary of Contents for B465

Reviews:

Related manuals for B465

Brands by name

Popular brands

Bosch B465, Installation And Operation Manual

Search results

Summary of Contents for B465

Reviews:

Related manuals for B465

Brands by name

Popular brands