Bosch B465 Installation And Operation Manual Download Page 17 | Manualshive

Page: 17 / 115

background image

Conettix Universal Dual Path Communicator

Installation | en

17

Bosch Security Systems, Inc.

Installation and Operation Manual

2017.11 | 05 | F.01U.311.207

4.5

Install the B465 in the enclosure

Refer to the B465 Quick Start Guide for more information.
Perform the following to install the module.

!

Warning!

The module is static sensitive. Touch earth ground before handling the circuit board to
discharge any static electricity from your body. Use a grounding strap while installing the
circuit board.

4.5.1

Mount the B46 (optional)

Refer to the B46 Install Guide for more information.

4.5.2

Connect earth ground

To help prevent damage from electrostatic discharges or other transient electrical surges,
connect the system to earth ground before making other connections. The icon indicates the
earth ground terminal. Use a recommended earth ground reference, such as a grounding rod
or a metal cold water pipe. Make the connection using 14 AWG (1.8 mm) to 16 AWG (1.5 mm)
wire.

Notice!

Do not use telephone or electrical ground for the earth ground connection. Do not connect
other control panel terminals to earth ground.

!

Caution!

Avoid electrostatic discharge. Always touch the earth ground connection with the icon first,
before beginning work on the control panel.

Notice!

In ground fault enabled systems, you might cause a ground fault when connecting a computer
to the B465 for programming.

4.6

Install the cellular plug-in communicator module (optional)

For cellular communication, use one of the following:
–

B440 Conettix Plug-in Cellular Communicator (3G Verizon, US only)

–

B441 Conettix Plug-in Cellular Communicator (Verizon, US only)

–

B442 Conettix Plug-in GPRS Cellular Communicator (outside the USA where approved)

–

B443 Conettix Plug-in HSPA+ Cellular Communicator (where approved)

–

B444 Conettix Plug-in LTE Cellular Communicator (Verizon, US only)

Install the plug-in module

1.

Power down the B465.

2.

Insert the plug-in module into plug-in stabilizing hole X, and then into the plug-in module
connector. Continue pressing the module into the connector until the retention clip
engages. Refer to callouts 1, 2, and 3 in

B465 overview, page 10

«
...
15
16
17
18
19
...
»

Summary of Contents for B465




















































































































Reviews:

No comments

Related manuals for B465

EL 2310-08E Series

Brand: Oval Pages: 80

Brand: Yezz Pages: 5

Brand: GoDark Pages: 2

Sprint Torcque XT

Brand: Kyocera Pages: 209

POLYCOM VTXTM 1000

Brand: Polycom Pages: 2

Brand: Planet Pages: 51

Brand: Mitel Pages: 56

Brand: AOC Pages: 22

Brand: Interlink electronics Pages: 16

Brand: Zte Pages: 2

Brand: Zte Pages: 116

Brand: Zte Pages: 46

Brand: Zte Pages: 172

Brand: Avvio Pages: 40

Brand: Avvio Pages: 46

Brand: Lanix Pages: 21

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands