Bosch B465 Installation And Operation Manual Download Page 113 | Manualshive

Page: 113 / 115

background image

Conettix Universal Dual Path Communicator

Specifications and certifications | en

113

Bosch Security Systems, Inc.

Installation and Operation Manual

2017.11 | 05 | F.01U.311.207

Contact ID report

(i = input number, 001-004)

(t = trouble type)

B465 Event

B465 Event #

1-373-99-iii
FIRE TROUBLE

When a B465 input that is configured for Fire
Trouble is shorted, the B465 makes a Panel
Fire Trouble event and sends a FIRE
TROUBLE report.

9

3-373-99-iii
FIRE TROUBLE (restoral)

When a B465 input that is configured for Fire
Trouble returns to normal after being
shorted, the B465 makes a Panel Fire
Trouble Restoral event and sends a, FIRE
TROUBLE Restoral report.

10

1-380-99-iii
BURGLARY TROUBLE

When a B465 input that is configured for
Burglary Trouble is shorted, the B465 makes
a Panel Burglary Trouble event and sends a
BURGLARY TROUBLE report.

9

3-380-99-iii
BURGLARY TROUBLE (restoral)

When a B465 input that is configured for
Burglary Trouble returns to normal after
being shorted, the B465 makes a Panel
Burglary Trouble Restoral event and sends a,
BURGLARY TROUBLE Restoral report.

10

1-602-99-000
PERIODIC TEST

When the B465 is configured to send test
reports it sends a PERIODIC TEST report.

36

1-608-99-000
PERIODIC TEST (system trouble
present)

When the B465 is configured to send test
reports and there is a module or input fault
it sends a PERIODIC TEST (system trouble
present) report.

37

«
...
111
112
113
114
115
»

Summary of Contents for B465




















































































































Reviews:

No comments

Related manuals for B465

Brand: T-Mobile Pages: 24

Brand: MTT Pages: 34

Brand: iBall Pages: 17

Brand: Sagem Pages: 115

Brand: Grandstream Networks Pages: 10

SMARTPHONE 3.2 LITE

Brand: Tesla Pages: 3

Brand: Planet Pages: 51

Brand: SoftBank Pages: 9

Brand: Mircom Pages: 40

Brand: Samsung Pages: 153

Brand: Tobii Dynavox Pages: 26

Brand: LG Pages: 185

Brand: NEC Pages: 165

Brand: NEC Pages: 101

Brand: Huawei Pages: 23

Brand: Huawei Pages: 10

POCKET PC PHONE

Brand: GENERAL MOBILE Pages: 74

AMPLIDECT295SOS-PRO

Brand: Geemarc Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands