Bosch B465 Installation And Operation Manual Download Page 49

Page: 49 / 115

Conettix Universal Dual Path Communicator

Configuration and Diagnostics | en

Bosch Security Systems, Inc.

Installation and Operation Manual

2017.11 | 05 | F.01U.311.207

Socket xx: Port
Number

This field displays the current open Port Numbers and Data Types (up to
32).

Modem Status

The information below shows in the appropriate fields. If no modem status is detected, the
following message appears: Modem status is not available.

Parameter

Description

Electrical Serial #
(ESN)

This field displays the B44x radio modem serial number.

Data Status

This field displays one of the following; Disconnected, Connecting, or
Connected.

Signal Strength

This field displays the current signal strength. One of the following
appears; Very good, Good, Marginal, Unacceptable, or Unavailable.

Module Status

Module Status shows only when there is a trouble status.

Summary of Contents for B465




















































































































Search results

Summary of Contents for B465

Reviews:

Related manuals for B465

Brands by name

Popular brands

Bosch B465, Installation And Operation Manual

Search results

Summary of Contents for B465

Reviews:

Related manuals for B465

Brands by name

Popular brands