background image

42

en | Configuration and Diagnostics

Conettix Universal Dual Path Communicator

2017.11 | 05 | F.01U.311.207

Installation and Operation Manual

Bosch Security Systems, Inc.

3.

Set up a connection on the new virtual serial COM port (for example, Port: COM7: B465
[COM7]). If the B465 is not connected to the computer, or the USB driver is not installed,
the B465 does not appear in the list.

4.

After the connection is established, press [Enter]. 
The B465 USB login window opens.

Figure

 

6.7: B465 USB login window

5.

Enter the password to log on. The default password is B465.
The user interface allows three attempts to enter the password correctly. After three
failed attempts, the B465 shows a Too

 

many

 

attempts error message, and the USB

interface enters into an idle state for 30 seconds. Repeat

 

Steps

 

3 through 6 at the

conclusion of 30 seconds.

6.

Press [Enter] to continue. The USB main menu opens.

Notice!

Please write down the password. If you forget your password we can only default the module
after it is returned and will not be able to help you restore the module in the field.

Summary of Contents for B465




















































































































Reviews: