Bosch B465 Installation And Operation Manual Download Page 15 | Manualshive

Page: 15 / 115

background image

Conettix Universal Dual Path Communicator

Installation | en

15

Bosch Security Systems, Inc.

Installation and Operation Manual

2017.11 | 05 | F.01U.311.207

4

Installation

Perform the following steps to install the module.

Notice!
B46 External Annunciator installation

Refer to the

B46 External Annunciator Installation Guide

(P/N: F01U312441) prior to installing

the enclosure for B465 module. There is a specific installation sequence you must follow to
avoid damaging the B46 module during the installation process.

4.1

Remove enclosure knockouts

Refer to Figure 4.1 below for knockout locations.

!

Caution!

Insert conduits into the enclosure knockout areas when running wire or cabling to reduce
wire/cable damage.

4.2

Mount the enclosure

Mount one of the following enclosures in the desired location to meet desired UL
requirements:
–

B10 Medium Control Panel Enclosure (white)

–

B10R Medium Control Panel Enclosure (red)

–

B11 Small Control Panel Enclosure (white)

–

B11R Small Control Panel Enclosure (red)

–

D8103 Universal enclosure (this enclosure requires the B12 mounting plate)

–

D8108A Attack Resistant Enclosure (this enclosure requires the B12 mounting plate)

Installing the enclosure:
1.

Remove any knockouts prior to installing the module.

2.

Mount the enclosure in the desired location. Use all enclosure mounting holes. Refer to
the mounting instructions supplied with the selected enclosure.

3.

Pull any necessary wires/phone lines into the enclosure.

Notice!
Electromagnetic interference (EMI) can cause problems on long wire runs

«
...
13
14
15
16
17
...
»

Summary of Contents for B465




















































































































Reviews:

No comments

Related manuals for B465

KXDT346 - DIGITAL PROPRIETARY TELEPHONE

Brand: Panasonic Pages: 2

Brand: Pantech Pages: 116

Brand: Yealink Pages: 361

Brand: Yealink Pages: 7

Brand: Yealink Pages: 4

Brand: Yealink Pages: 2

Brand: Yealink Pages: 7

Brand: Samsung Pages: 343

OpenStage SL4 professional HiPath Cordless...

Brand: Unify Pages: 80

Brand: M4 Pages: 19

Brand: Audiovox Pages: 137

Brand: NAPCO Pages: 24

Basic Digital Phone

Brand: Inter-Tel Pages: 90

Brand: Wistec Pages: 60

Enterprise IP Phone

Brand: Grandstream Networks Pages: 56

Brand: KARBONN Pages: 33

Brand: ShoreTel Pages: 3

Brand: Haier Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands