Home
/
Black Box
/
LS1016A
/
User Manual

Black Box LS1016A, User Manual

Share

Page: 164 / 450

Black Box LS1016A User Manual Download Page 164

Filters and Network Address Translation

164

BLACK BOX

®

Advanced Console Server

Target Extensions

Iptables can use extended target modules. The following are included in the standard
distribution.

LOG

Turn on kernel logging of matching packets. When this option is set for a rule, the Linux
kernel will print some information on all matching packets (like most IP header fields) via the
kernel log (where it can be read with syslog-ng).

REJECT (filter table only)

This is used to send back an error packet in response to the matched packet: otherwise it is
equivalent to DROP. This target is only valid in the INPUT, FORWARD and OUTPUT chains,
and user-defined chains which are only called from those chains. Several options control the
nature of the error packet returned:

SNAT (nat table only)

This target is only valid in the nat table, in the POSTROUTING chain. It specifies that the
source address of the packet should be modified (and all future packets in this connection
will also be mangled), and rules should cease being examined. It takes one option:

- -source-port [port[,port]]

Match if the source port is one of the given ports.

- -destination-port [port[,port]]

Match if the destination port is one of the given ports.

- -port [port[,port]]

Match if the both the source and destination port are
equal to each other and to one of the given ports.

- -log-level level

Level of logging (numeric or see syslog.conf(5)).

- -log-prefix prefix

Prefix log messages with the specified prefix; up to 29 letters
long, and useful for distinguishing messages in the logs.

- -log-tcp-sequence

Log TCP sequence numbers. This is a security risk if the log is
readable by users.

- -log-tcp-options

Log options from the TCP packet header.

- -log-ip-options

Log options from the IP packet header.

«
...
162
163
164
165
166
...
»

Summary of Contents for LS1016A



































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands