C
HAPTER
37
| Spanning Tree Commands
– 874 –
D
EFAULT
S
ETTING
By default, the system automatically detects the speed and duplex mode
used on each port, and configures the path cost according to the values
shown below. Path cost “0” is used to indicate auto-configuration mode.
When the short path cost method is selected and the default path cost
recommended by the IEEE 8021w standard exceeds 65,535, the default is
set to 65,535.
Table 98: Default STA Path Costs
Port Type
Short Path Cost
(IEEE 802.1D-1998)
Long Path Cost
(802.1D-2004)
Fast Ethernet
100,000
100,000
Gigabit Ethernet
10,000
10,000
10G Ethernet
1,000
1,000
C
OMMAND
M
ODE
Interface Configuration (Ethernet, Port Channel)
C
OMMAND
U
SAGE
◆
This command is used by the Spanning Tree Algorithm to determine the
best path between devices. Therefore, lower values should be assigned
to ports attached to faster media, and higher values assigned to ports
with slower media.
◆
Path cost takes precedence over port priority.
◆
When the path cost method (
page 866
) is set to short, the maximum
value for path cost is 65,535.
E
XAMPLE
Console(config)#interface ethernet 1/5
Console(config-if)#spanning-tree cost 50
Console(config-if)#
spanning-tree edge-
port
This command specifies an interface as an edge port. Use the
no
form to
restore the default.
S
YNTAX
[
no
]
spanning-tree edge-port
D
EFAULT
S
ETTING
Disabled
C
OMMAND
M
ODE
Interface Configuration (Ethernet, Port Channel)
Summary of Contents for LGB6026A
