Black Box LGB6026A Management Manual Download Page 320 | Manualshive

Page: 320 / 1289

background image

– 318 –

C

HAPTER

14

| Security Measures

ARP Inspection

C

OMMAND

U

SAGE

Enabling & Disabling ARP Inspection

◆

ARP Inspection is controlled on a global and VLAN basis.

◆

By default, ARP Inspection is disabled both globally and on all VLANs.

■

If ARP Inspection is globally enabled, then it becomes active only on
the VLANs where it has been enabled.

■

When ARP Inspection is enabled globally, all ARP request and reply
packets on inspection-enabled VLANs are redirected to the CPU and
their switching behavior handled by the ARP Inspection engine.

■

If ARP Inspection is disabled globally, then it becomes inactive for
all VLANs, including those where inspection is enabled.

■

When ARP Inspection is disabled, all ARP request and reply packets
will bypass the ARP Inspection engine and their switching behavior
will match that of all other packets.

■

Disabling and then re-enabling global ARP Inspection will not affect
the ARP Inspection configuration of any VLANs.

■

When ARP Inspection is disabled globally, it is still possible to
configure ARP Inspection for individual VLANs. These configuration
changes will only become active after ARP Inspection is enabled
globally again.

◆

The ARP Inspection engine in the current firmware version does not
support ARP Inspection on trunk ports.

C

ONFIGURING

G

LOBAL

S

ETTINGS FOR

ARP

I

NSPECTION

Use the Security > ARP Inspection (Configure General) page to enable ARP
inspection globally for the switch, to validate address information in each
packet, and configure logging.

CLI R

EFERENCES

◆

"ARP Inspection" on page 792

C

OMMAND

U

SAGE

ARP Inspection Validation

◆

By default, ARP Inspection Validation is disabled.

◆

Specifying at least one of the following validations enables ARP
Inspection Validation globally. Any combination of the following checks
can be active concurrently.

■

Destination MAC – Checks the destination MAC address in the
Ethernet header against the target MAC address in the ARP body.
This check is performed for ARP responses. When enabled, packets

«
...
318
319
320
321
322
...
»

Summary of Contents for LGB6026A










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for LGB6026A

DynaGST/2402G GEP-33224T-1

Brand: UNICOM Pages: 1

Cleveland Controls RSS-498-013

Brand: UNICONTROL Electronic Pages: 2

Brand: Communica Pages: 5

Brand: WoMaster Pages: 2

Brand: JAR Systems Pages: 2

Brand: Surefire Pages: 2

Brand: SUCO Pages: 2

Brand: FCI Pages: 78

JTECH-4KPIP0401

Brand: J-Tech Digital Pages: 10

Magnum CS14 Series

Brand: GarrettCom Pages: 76

Brand: AbleNet Pages: 6

Brand: Linkskey Pages: 2

Brand: Kramer Pages: 4

Brand: Konig Pages: 52

Brand: The Siemon Company Pages: 2

Brand: 3One data Pages: 9

Brand: Black Box Pages: 15

Brand: ATEN Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands