Bandai Namco RAZING STORM Operation Manual Download Page 23

Page: 23 / 136

5. INSTALLATION

If the carry-in passage is sufficiently tall, the following procedure is not necessary.

In that case, proceed to “5-3 Assembly” on page 22.



The projector weighs approximately 31 kg. Removal of the projector should

be performed by at least three persons to prevent accidents.

Remove the three torx bolts (M5 X 12), then dismount the front plate door.

Using the Instructions on P. 79, 8-3-1(1) Replacing the LED Boartd steps
through remove the LED Sensor cover from the game.

5-2-1 Separating the Projector Tower Assy (when required due to passage conditions)
- To be conducted by a technician only -

WARNING

Connectors

Torx bolt (M5 x 12)

Front plate door

Torx bolt

(M5 x 20)

Torx bolt

(M5 x 12)

Summary of Contents for RAZING STORM









































































































































Search results

Summary of Contents for RAZING STORM

Reviews:

Related manuals for RAZING STORM

Brands by name

Popular brands

Bandai Namco RAZING STORM, Operation Manual

Search results

Summary of Contents for RAZING STORM

Reviews:

Related manuals for RAZING STORM

Brands by name

Popular brands