Page 8
Confi guration Planning Procedure:
Use the following procedure to complete and fi ll out the
Confi guration Planning Worksheet, opposite page:
1
Determine the
number of system fluids
to be
dispensed.
2
If the number of fl uids in the system is 3 or 4, or if
you will confi gure for future expansion, you must use
the
standard fl uid confi guration
plan. Up to 16 stations
are permitted.
3
If the number of fl uids in the system is 2 and you
are not confi guring for future expansion, you must
use the
dual fl uid confi guration
plan. Up to 32 stations
are permitted.
4
If the number of fl uids in the system is 1 and you are
not confi guring for future expansion, you must use
the
single fl uid confi guration
plan. Up to 64 stations
are permitted.
5
Above the station blocks for the service area,
write in
the fl uid types
for each of the fl uids to be dispensed,
working left to right. Fill in both LH and RH
fl uid type
blocks. Also enter
fl uid types
in the designated row of
the air station block.
6
In the fi rst service area station block (next to SC01),
fi ll in the station row
: use 1,1,1,1 for
standard plan
,
1,1,2,2 for
dual fl uid plan
, 1,2,3,4 for
single fl uid plan
.
7
In the second service area station block (next to SC02),
fi ll in the station row
: use 2,2,2,2 for
standard plan
,
3,3,4,4 for
dual fl uid plan
, 5,6,7,8 for
single fl uid plan
.
8
Continue fi lling in additional station rows
, using
sequential numbering in a similar manner, until the last
entered number is equal to the total number of stations
in your system.
9
Now enter
check marks
in all of the numbered station
blocks, but only beneath port positions which will
be used.
10
Now
compile an equipment requirements list
,
next column, using the information on the Planning
Worksheet.
11
During worksheet preparation, for each fl uid, enter
tank size
,
alarm level amount
,
fluid type
and
estimated
current tank level
(all in gallon units). At
factory set-up time, Balcrank will add
meter PPG
factors.
At fi eld installation time, adjust exact tank current-level
amounts.
12
Record the
user name and location, distributor
name and distributor PO number.
13
Indicate by
checked box
whether the system will
include a
ticket printer
. If a
quick lube bay
is to be
used, identify the designated quick lube bay.
14
All systems are
factory pre-programmed
and will
be shipped with a copy of your completed
planning
sheet
, with fi nal information added.
Save this information
as a record of confi guration for
future use in equipment expansion or repair.
Planning:
Confi guration Planning Procedure
Equipment list:
3120-030 Smart Controller
TM
.
Order one per checked
station
block
, including the air block.
3120-031 Ready Light
. Order one per
check mark
in the
combined service area station blocks.
3120-032 Fluid Solenoid Valve
. Order one per
check
mark
in the combined service area station blocks.
3120-033 Air Solenoid Valve
. Order one per
fl uid used
in the air station block.
3110-006P Spectrum 100 Console
. Order one per
system
.
3120-039 Extension Cable for Printer
. (optional) Allows
printer to be up to 250 ft from console. Use two to go
500 ft. max.
3120-035 Ticket Printer.
(optional). Order one per
system
.
3120-026 Host PC Interface.
(optional). Order one per
system
. Do not combine printer with PC interface.
3120-103 Impulse Meter
. Order one per
check mark
in
the air station block.
3123-xxx Solenoid Cable, 3121-xxx Comm/Power
Cable, 3122-xxx Impulse Meter Cable
. Use the system
wiring diagram to assist in identifying where each cable
type is used. Actual facility dimensions will determine best
order lengths. Select cable spools lengths from a range of
model choices, shown in the Balcrank price list.
Defi nitions:
SC:
Smart Controller, an electronic control card which manages operation
of fl uid solenoid valves in the service bay areas and air solenoid valves
in the pump room.
Port:
A solenoid actuator location on the electronic Smart Controller.
A port equates to a single fl uid dispense point, or to a single on/off
valve for an air pump.
Station:
an individual dispensing location, with 1 to 4 dispense points,
in the service area. Note that a station may serve more than one bay
whenever dispensing handles are shared by operators.
Model Description
Quantity
3120-030
Smart Controller
3120-031
Ready Light
3120-032
Fluid Solenoid Valve
3120-033
Air Solenoid Valve
3110-006P
Queuing Console
3120-039
Printer Extension Cable
3120-035
Ticket Printer
3120-103
Impulse
Meter
3123-xxx
Solenoid
Cable
3121-xxx
Comm/Power
Cable
3122-xxx
Impulse Meter Cable
3120-026
Host PC Interface
