Avaya Media Gateway G350 Maintenance Manual Download Page 83

Page: 83 / 332

Avaya Communication Manager controlled maintenance

AN-LN-PT (Analog Line Port)

Maintenance of the Avaya G350 Media Gateway

June 2004

Station Status and Translation Audits and
Updates Test (#36)

This test updates the analog port’s message lamp state (if it has one) and translations with information in
the software.

Table 38: TEST #36

Station Status and Translation Audits and Updates 1 of 2

Error
Code

Test
Result

Description/ Recommendation

ABORT

Necessary system resources could not be allocated to run this test.

Retry the command at 1-minute intervals no more than 5 times.

If the test continues to abort, escalate the problem.

1004

ABORT

A valid call seized the port during the test and aborted the test.

Use the display board GGGVSpp command to determine the station
extension.

Use the

status station

extension

command to determine the service

state of the port.

If the port is in use, wait until the port is idle before testing. Retry the
command at 1-minute intervals no more than 5 times.

If the test continues to abort, escalate the problem.

1005

ABORT

This test was aborted due to a configuration problem. The test is not
applicable for this type of analog port. This error can be ignored.

1006

ABORT

The port is out-of-service. The

busy station

extension

command has

been given to this port.

Look for error type 18 (port busied out) for this port. If this error is
present, release the port (

release station extension

), and run the test

again.

Make sure that the terminal is connected and in service, and then retest.

2000

ABORT

Response to the test request was not received within the allowable time
period.

2100

ABORT

System resources required to run this test are not available.

Retry the command at 1-minute intervals no more than 5 times.

If the test continues to abort, escalate the problem.

FAIL

The switchhook audit failed. This result does not indicate a hardware
problem. The other updates were not performed because of this failure.
This may occur if the audit is performed at the same time the terminal
equipment goes off-hook.

Use the

status station

extension

command to determine when the

port is available.

Retry the command at 1-minute intervals no more than 5 times.

If the test continues to fail, escalate the problem.

1 of 2

Summary of Contents for Media Gateway G350













































































































































































































































































































































Search results

Summary of Contents for Media Gateway G350

Reviews:

Related manuals for Media Gateway G350

Brands by name

Popular brands

Avaya Media Gateway G350, Maintenance Manual

Search results

Summary of Contents for Media Gateway G350

Reviews:

Related manuals for Media Gateway G350

Brands by name

Popular brands